BA series-connected load draws a current i(t) = 4 cos(315t + 10°) A when the applied voltage is v(t) = 120 cos(315t - 20°) V. Compute the apparent power and the power factor of the load. Determine the element values that form the series- connected load.

BA series-connected load draws a current i(t) = 4 cos(315t + 10°) A when the applied voltage is v(t) = 120 cos(315t - 20°) V. Compute the apparent power and the power factor of the load. Determine the element values that form the series- connected load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: For the system shown, (a) find the average/real power Pg and reactive power Q, supplied by the…

A: Given, E = 50 V Load 1= 100 VAr , 200W Load 2= 100 VAr , 200W Load 3= 200 VAr , 0W Load 4= 200 VAr ,…

Q: In the circuit shown below 1. Find average power of the resistor R 2. Find value of R 3. Find power…

Q: Q3. Each phase of a delta-connected load comprises a resistance of 300 and an 80µF capacitor in…

Q: Q3) By using the circuit given below; Find the total value of active power, reactive power, apparent…

A: Given parameters are: Load1: S1=5kVA pf=cosΦ1=0.65(lagging) Load 2: Q2=2000VAR…

Q: Q2: For the circuit shown below, determine the apparent power delivered by the source, power…

A: First we will calculate node voltage by nodal analysis. power loss =I2×R. power factor= cos(angle…

Q: In Industry, three Inductive loads, each of resistance R = 26 ohms and inductance L= 0.08 H are…

A: Given, a three inductive load delta connected system having, Resistance, R = 26 ohms Inductance, L =…

Q: A 270-V rms 80-Hz supply serves a load that is 12 kW, 17 KVAR (capacitive), and 25 KVAR (inductive).…

Q: (a) Calculate real power, reactive power and apparent power dissipated by each component (resistor,…

Q: In Industry, three Inductive loads, each of resistance R = 30 ohms and inductance L = 0.13 H are…

A: In the Star Connection, the 3 winding's similar endpoints are connected to a common point known as…

Q: Q2. Calculate average, apparent, complex power delivered to the load Z, = 8+j6 ghm. Also estimate…

Q: A 4-kW, 110-Vrms load, as shown below, has a power factor of 0.82 lagging. Find the value of the…

Q: Given the circuit below, determine a) the overall power factor, b)the real power dissipated, c.) the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Given voltage source = 100V∠0°, give the value of real power, apparent power, and reactive power…

Q: If a load absord 20KVA at the leading power factor of 0.6 Write the complex form of power

Q: A 400V, 60HZ, three-phase star-con supplies a delta-connected load, each phase of which has a…

A: Given data f=60 HzVL=400VRph=30 ohmLph=40 mHXLph=2×3.14×60×30×10-3=11.30 ohmrline=2.20 ohm…

Q: Load 1 Load 2 Load 3

Q: In the given circuit below, compute the active, reactive, apparent power and the power factor of the…

A: For the given circuit diagram shown Active, reactive, apparent power and power factor of the load…

Q: POWER ANALYSIS IN CIRCUITS find, the complex power absorbed in: a. 1 ohm b. capacitor -j10 ohm…

Q: Q3. Each phase of a delta-connected load comprises a resistance of 300 and an 80µF capacitor in…

Q: The load ZL in the circuit of Figure consistsof a 25-Ω resistor in series with a 0.1-H…

A: The impedance of the inductance is, The expression of the load is,

Q: السؤال 4 The Thevenin impedance of a source is ZTh = 101+ j 582, while the Thevenin voltage is VTh =…

Q: Determine the apparent power and the power factor if a series-connected load has current, i(t) = 5…

A: Apparent power = VI* where V and I are rms value. Impedance = V / I.

Q: Z, Source Transmission line Load

A: We will find out current for given circuit

Q: Two parallel-connected impedance Z₁ = 8 + j 6 2 and Z₂ = 10 +j 2 2 are connected in series with 15 2…

Q: In Industry, three Inductive loads each of resistance R = 33 ohms and inductance L = 0.11 H are…

A: A star connected load has, Per phase resistance (Rph)= 33 ohm Per phase inductance (Lph)= 0.11 H…

Q: The load on a 120-V, 60 Hz supply is 5KW (resistive), 8 KVAR (inductive), and 2 KVAR (capacitive).…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: In the given circuit below, compute the active, reactive, apparent power and the power factor of the…

A: Given data Voltage is VS(t) = 141.42 cos(314t+60) Assuming value of y = 5. Calculating capacitive…

Q: A series-connected load draws a current i(t) = 4 cos(100πt + 10°) A when the applied voltage is v(t)…

A: Given that i(t) = 4 cos(100πt + 10°) A=4∠10° Av(t) = 120 cos(100πt − 20°) V=120∠-20° A (i)…

Q: A balanced, three-wire, delta-connected, three-phase load has a phase voltage of 400 V, a line…

A: Given, A balanced three wire delta connected three phase load has, Phase voltage, Vph=400 V. Line…

Q: A series connected load draws a current 0 = 4 cos(100xt + 10") A when the applied voltage is () -…

A: Impedance is represented as Z=R+jX, where R represents resistance and X represents reactance. The…

Q: Figure Q2 below shows a manufacturing plant connected to three phase 3600 V line of wye…

A: Given data: The source is wye (star) connected and operating frequency is f=50 Hz. Sending end line…

Q: Find the total impedance, total current drawn by the system, total power (apparent) delivered by the…

Q: Consider the circuit shown below. Determine the following: a) Find the phasor current I. b) Active…

A: In this question , we will find current , active power, reactive power , apparent power and power…

Q: The circuit given in the figure is given as vs (t) = √2 * 50cos (4t + 60). a) Calculate the…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: From the circuit below, if R = 58, determine the maximum power absorbed by the load impedance ZL…

A: To find the maximum power absorbed by the load impedance ZL

Q: Q.14: In the circuit shown, the load consumed (500VA) with (0.8) power factor. Compute the coupling…

Q: 6. A 240-Vms 50-Hz supply serves a load that is 10 kW (resistive), 15 kVAR (capacitive), and 22 KVAR…

Q: Q2) Two loads connected in parallel are respectively 2Kw at a p.f. of 0.75 leading and 4Kw at a p.f.…

A: In the question Two loads are connected parallel One is 2kW at 0.75 PF leading Second 4kW at…

Q: . For the circuit given below Find Thevenin equivalent circuit Find maximum average power delivered…

A: According to Thevenin's theorem, any linear circuit, no matter how complicated, may be simplified to…

Q: A load consists of R=78 Q, XL=71 Q and Xc=47 Q. All the elements are connected in parallel across…

A: Given, a load consist of R= 78 ohm XL= 71 ohm XC= 47 ohm All elements are connected in parallel…

Q: Electrical Engineering For the three-phase circuit obtain a) Obtain the complex power supplied by…

A: In this question we need to find a complex power supply by source and power factor

Q: A power circuit is shown below. The active and reactive powers of the 3 loads and their types are as…

Q: For the circuit shown below, find Thevenin's equivalent circuit and determine the load impedance…

A: The maximum average power of the voltage is as follows: Impedance of inductor ZL=jωL=j400×0.2=j 80…

Q: Find the complex power supplied by the source and the power factor of the source for the network…

Q: LEARNING EXAMPLE f=60HZ,|Vine =34.5kV rms. Required:pf = 0.94leading %3D a Balanced load Balanced 24…

A: The solution is given below

Q: 2.Calculate the real power taken by each impedance and voltage source in the circuit below.Show that…

Q: For the circuit shown below, R = 2 2. L-20 mH, and E= 100V. The ac source is 120 V rms at 60 Hz. (a)…

A: As per Bartleby policy we can answer only 3 subparts at a time. So I am solving first three for you.…

Q: Given the circuit below and the associated set of voltages and currents, the real Power delivered by…

Q: A source supplies power to the following three loads connected in parallel: (1) a lighting load…

A: Given a source supplies power to the following loads 1)Lighting load 10kw 2) Induction motor 10 KVA…

Q: Consider the system as shown in figure Q3, supplies 100 kW at a power factor of 0.85 lagging. The…

A: power at receiving end = sending end power- losses in transmission line. Receiving end voltage=…

Concept explainers

Photoelectric

The photoelectric effect occurs when light (or similar incident radiation, including X-rays) falls on material together with a metal plate and causes it to emit electrons. The discovery of the photoelectric effect led to important new theories (and to a Nobel Prize for Albert Einstein). Photoelectric cells, or photocells, are utilized in burglar-alarm light detectors and garage-door openers (each employs a through-beam of light this is broken when something movements throughout it), and also to play soundtracks on film movies (in which a light beam shines through the soundtrack encoded at the film and is "read" with the aid of the photocells).

Question

question is in image

BA series-connected load draws a current i(t) = 4 cos(315t + 10°) A when
the applied voltage is v(t) = 120 cos(315t - 20°) V. Compute the apparent power and
the power factor of the load. Determine the element values that form the series-
connected load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve A line with impedance of 1 +j 0.32 Q is used to deliver power to a load. The load is inductive and the load voltage is 220 0° Vrms at 50Hz. If the load operates at 40 kw with a power factor of 0.75 lagging, determine the complex power in both the load and the line current. 9.2) draw the phasor diagram for the circuit, 9.3) calculate the power savings if power factor is changed to .95.
A 3- phase star connected load has resistance of 4 Ω, inductance of 15.9mH & a capacitive reactance of 6 Ω respectively in R Y & B phases. If the load is connected to 400V, 50Hz supply, Calculate the neutral current ,Find the total power absorbed by the load., Draw the current and voltage phasors
The impedance of an electrical circuit is (30 − j50) ohms. Determine (a) the resistance, (b) the capacitance, (c) the modulus of the impedance, and (d) the current flowing and its phase angle, when the circuit is connected to a 240V, 50 Hz supply.
A 3- phase star connected load has resistance of 4 Ω, inductance of 15.9mH & a capacitive reactance of 6 Ω respectively in R B & Y phases. If the load is connected to 400V, 50Hz supply, i. Calculate the neutral current .ii. Find the total power absorbed by the load.iii. Draw the current phasors
The circuit given in the figure is given as vs (t) = √2 * 50cos (4t + 60). a) Calculate the equivalent load impedance. Indicate whether the load is inductive or capacitive.b) Calculate the load current Ḭload. Write the time dependent good (t) expression.c) Calculate the load voltage V̰load. Write the time dependent expression vload (t).d) Calculate the active, reactive and apparent power of the load. Determine the power factor.
Consider the system shown. E is 240 V. If the three loads are 200 W, 400 W and 1000 W resistive, respectively, determine the apparent power delivered to the system, the real power and the reactive power.
. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design
The load on a 120-V, 60 Hz supply is 5KW (resistive), 8 KVAR (inductive), and 2 KVAR (capacitive). Find the following: a) total kilovolt-amperes, b)power factor of the combined loads, c) current drawn from the supply, d) capacitance needed to establish unity power factor, e) capacitive reactance needed to establish unity power factor, f) the current drawn from the supply at unity p.f.
a power station has a connected load of 48MW. the energy generated for the year is 61500MWh. if the station has a load factor of 35%. solve the demand factor of the station. Subject: Distribution System and Substation Design
The circuit given in the figure is given as vs (t) = √2 * 50cos (4t + 60). (y=4) 1)Calculate the equivalent load impedance. Indicate whether the load is inductive or capacitive 2)Calculate the load current Ḭyük. Write the time dependent expression Iyük (t). 3)Calculate the load voltage V̰yük. Write the time dependent expression Vyük(t). 4)Calculate the active, reactive and apparent power of the load. Determine the power factor.
Q2 In Industry, three Inductive loads, each of resistance R = 32 ohms and inductance L = 0.04 H are connected in Delta to a 425 V, F = 50 Hz, 3 phase supply. Find the following below: i) Phase Impedance, Zp = ii) Phase Voltage, Vp = iii) Phase current, Ip = !3! iv) Line current, I= iiv) The Total Power Consumed, P=
A series circuit containing a noninductive resistance of 3 Ω and a coil is connected to a 120 V, 60 Hz supply. The current is 25 A. The true power, as indicated by a wattmeter, is 2500 W. Determine: the power factor of the series circuit. the effective resistance of the coil. the impedance and inductive rea ctance for the coil. the power factor of the coil