5- Estimate the solubility parameters of Aniline. Furthermore, the atomicweights of C, H, and N respectively, 12.01, 1.01, and 14.0067 g/mol. Thedensity of Aniline is 1.18 g/cm.N=N (O NH2Table 1 Molar Attraction Constants, E (cal cm)/mol.GroupEPhenyl-N735Phenyl-NH2658-NH2 (aromatic)342-N=N- (aromatic)-11.4

Solution. We can find solubility parameter for given compound form given molar attraction constant…

Answered: 5- Estimate the solubility parameters…

5- Estimate the solubility parameters of Aniline. Furthermore, the atomic weights of C, H, and N respectively, 12.01, 1.01, and 14.0067 g/mol. The density of Aniline is 1.18 g/cm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

101) Which data is used in designs where weight and energy are considered together?A) elastic modulusB) yield strengthC) special strengthD) breaking strengthE) tensile strength 102) mass diffusion (spreading) is defined by which law?a) faradayB) archimedesC) fickD) hume-rotaryE) exchange 103) which should be valid for the formation of the interphase?A) high electronegative differenceB) atomic radius similarityC) full resolutionD) limited resolutionE) atomic size difference
Derive expression for the lumped analysis in terms of Fourier and Biot numbers.
Nylon 6,6 is a thermoplastic polymer with high mechanical strength, high resistance to chemical environments, and good stability under heat. Therefore, it is well suited to be used in 3D structural objects. A cylindrical nylon 6,6 pipe is made by injection molding. The pipe is 1 m long with an outer diameter of 8cm, and a thickness of 2mm. The crystallinity of the pipe is 25%. The density and associated percent crystallinity for two nylon 6,6 samples are measured as below: ρ(g/cm3) crystallinity (%) 1.190 67 1.155 44 If the degree of polymerization is 500, calculate the number of chains in the pipe. (Assume the chains are equal in length).
Nylon 6,6 is a thermoplastic polymer with high mechanical strength, high resistance to chemical environments, and good stability under heat. Therefore, it is well suited to be used in 3D structural objects. A cylindrical nylon 6,6 pipe is made by injection molding. The pipe is 1 m long with an outer diameter of 8cm, and a thickness of 2mm. The crystallinity of the pipe is 25%. The density and associated percent crystallinity for two nylon 6,6 samples are measured as below: ρ(g/cm3) crystallinity (%) 1.190 67 1.155 44 Calculate the density of this pipe, which has 25% crystallinity.
A sample of lead has a mass of 31.00 kg and a density of 1.130 x104 kg/m3 at 0°C. (Assume the average linear expansion coefficient for lead is 2.900 x10-5(°C−1).) What is the density of lead at 95.00°C? (Give your answer to four significant figures.)
(a ) Rhodium has an atomic radius of 0.1345 nm and a density of 12.41 g/cm^3 . Determine whether it has an FCC or BCC crystal structure. (Note: It has an atomic weight of 102.91 g/mol.) (b) If aluminum diffused into a thick slice of silicon with no previous aluminum in it at the temperature of 1100 degrees celcius for 6 hours, what is the depth below the surface at which the concentration is 1016 atoms/cm^3 if the surface concentration is 1018 atoms/cm^3 . D=2x10^(-12) cm^2 /s for Al diffusing in Si at 1100 degrees celcius.
Show the miller-bravais index for a HCP structure.
a) List any four experimental methods to find the stress concentration factor. b) Explain how stress concentration can be reduced when a notch is unavoidable in a mechanical component with neat sketches?
Consider the following rotational temperatures of diatomic molecules: qr(N2) = 2.9K, qr(HD) = 64.7K Assuming classical behaviour (i.e. continuum approximation): (i) Estimate the number of accessible rotational energy levels at 290 K for both molecules. (ii) In which case would the classical approximation be accurate?
1- The density of the elemental magnesium crystal structure, which is in the face centered cubic structure, is 1,738 g / cm3. Specify the side lengths of the crystal lattice. 2-Polonium is an element with a simple cubic crystal arrangement. Find the radius of the polonium atoms in this structure with a density of 9.4 g / cm3 and a weight of 209 g / atom. 3- A wire with a diameter of 9.6 mm is pulled with a force of 18,000 N. With this loading, the initial length of the wire that grows 1.5 mm is 400 mm. Find the engineering voltage.
1. Choose the material that is brittle, a poor thermal conductor, a good thermal insulator, and can withstand high temperatures. a. Ceramics b. Composites c. Polymers d. Metals 2. Choose the substance with the greatest surface tension. a. C9H20 b. C12H26 c. C6H14 d. C24H50 3. Condensation polymers A. Are deposited in molds by condensing vapors B. Also release a small molecule such as water when they are formed C. Usually are made from monomers containing one or more C=C bonds D. None of the Above
The only alkali metal halides that do not adopt the NaCl structure are CsCl, CsBr, and CsI, formed from the largest alkali metal cation and the three largest halide ions. These crystallize in the cesium chloride structure (shown here for CsCl). This structure has been used as an example of how dispersion forces can dominate in the presence of ionic forces. Use the ideas of coordination number and polarizability to explain why the CsCl structure exists.