5) The kind of stress in flange portion of a partially drawn cylindrical cup when deep drawing without a blank holder is tensile in all three directions no stress in the flange at all, because there is no blank holder tensile stress in one direction and compressive stress in other direction tensile in two directions and compressive in third direction

Q: Differentiate normal axial loading from bending loading. Support your answer with neat explanatory…

A: The normal axial loading is defined as loading which acts on the cross sectional area of the beam…

Q: Distinguish between simple and indirect shear stress?

A: Simple shear stress also known as direct shear stress is the shear stress developed due to a…

Q: Why do the Ductile materials fail in shear?

A: Ductile materials are the materials which goes plastic deformation before the fracture. When any…

Q: Q2 Find the stress in steel bar

A: P = 10 KN Diameter = 14 mm = 0.014 m

Q: 1. What is the difference between direct and shear stress?

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: In pure torsion, the maximum torsional stress is at the center of the

A:

Q: 4. Write the relations used for maximum stress when a machine member is subjected to tensile or con…

A:

Q: 5-in stress strain curve the engineering stress will decrease after the tensile strength point?

A: Given data  To draw the stress strain diagram.

Q: Where should the internal resultant shear force be directed?

A: Direction for the internal resultant shear force will be opposite to the net force acting on the…

Q: What is Longitudinal Stress?

A: The stress produced along the length of an object due to the presence of forces which are equal and…

Q: Part 2 As the area under the stress-strain curve decreases, the toughness___________.   stays the…

A: Toughness: The capacity to absorb the energy of the material before the failure is known as…

Q: 1. If failure occurs in tension, why is shear important? Why is torsional load called pure shear?

A: Solution:

Q: Give an example of the Absolute Maximum Shear Strain?

A:

Q: What is the relationship between moment and shear?

A: The shear force and bending moment are related to each other through a differential equation. The…

Q: Q3/Fill the blanks with its suitable answer. 1) In a successful wire drawing process, the maximum…

A: Wire drawing is a process used to reduce the cross-section of the wire by pulling the wire through…

Q: bearing plate 15⁰ 20⁰ 25⁰ Cross- sectional Area

A:

Q: Identify the indirect force in the following Select one: O Tensile O Both Tensile and Compressive O…

A: Solution:

Q: Strain hardening is more visible in _______ process. a. Hot drawing b. Cold rolling c. Hot rolling…

A: Strain hardening is the process in which strain is generated in the metal due to continuous…

Q: . What is the longitudinal stress developed in

A: To find Longitudinal stress

Q: What is the formula for shear stress?

A: Shear stress: It is defined as the ratio of shear force acting laterally to the cross section of…

Q: Distinguish between the Normal and Shear Stress Components?

A: Normal and shear stress components are distinguished by their direction with respect to the area on…

Q: What is the difference between direct and shear stress?

A: The difference between direct and shear stresses are: 1. Direct stresses are induced in the body…

Q: - Differentiate between engineering stress and true stress.

A: Stress: It is the ratio of the load applied on the body per unit area

Q: What Fundamental problems occur in finding the resultant Internal normal force?

A: The resultant internal force is defined as the force, which is the result of resisting forces in the…

Q: Since both the force that cause Bearing Stress to Normal Stress is perpendicular to the cross…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: a) Differentiate between Normal, Shearing and Bearing Stress.

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: The 6 kN force is in the vertical direction, while the P=7.5 kN force is in the z direction.Since…

A:

Q: What are principal stresses?

A: The highest and the lowest value of the normal stress acting at a point is known as the principal…

Q: 5-In stress strain curve the engineering stress will decrease after the tensile strength point?

A: To give proper explanation of the above statement.

Q: Describe the hydrostatic stress?

A: When a force is imparted on a body, an internal resisting force is set up into the body, impeding…

Q: With a suitable example explain the difference between True stress-strain and Engineering…

A:

Q: (a) Maximum tensile flexural stress (Indicate where it occurs what section and where in the…

A: Given that ,  w=5kN/mP=15.11kN

Q: A spherical pressure vessel has a 1.5-ft inner radius and 3/16-in. wall thickness. If the working…

A:

Q: When a force is applied to a piece of material In such a manner as to twist it, the material is said…

A: A shaft is rigidly clamped at one end and twisted by a force at the other end then the shaft is in…

Q: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b)…

A: 1 Flanging and hemming are variation of sheet metal bending operations. Hence option B and C are the…

Q: How do the magnitude and direction of the principal stress change from point to point within a beam?

A: Given: A beam is loaded.  Explanation: Consider a beam which is loaded at a point shown below:

Q: How can the Maximum In-Plane Shear Stress determined?

A: The expression of the principal stress in a plane is given by,…

Q: Write a short note on Strength, Malleability and Tensile Strain

A: STRENGTH: The strength of the material is it's bility to withstand an applied load without failure…

Q: What is the ratio of maximum shear stress to average shear stress for a circular şection?

A:

Q: How can the stress coordinates of the points on the curves be determined?

A: To explain  How can the stress coordinates of the points on the curves be determined? Concept used…

Q: If you twist a body, what is produced. (axial or shear stress)

A: Let us assume a shaft of d diameter shaft.  Twist is applied to the shaft.

Q: the value of estimated shear yield stress,

A: Given; Homogeneous state of stress for a metal part undergoes plastic deformation is given in…

Q: 1. Is there a true stress strain curve for shear loading, if how will it be different from the…

A: Generally speaking, curves representing the relationship between stress and strain in any form of…

Q: What is Multiaxial Stress?

A: Multiaxial stress states due to the action of various external loads exist at the considered point…

Q: 4. Write the relations used for maximum stress when a machine member is subjected to tensile or com-…

A: Let a machine member is loaded with tensile stress and shear stress.

Q: Mises criterion, the yield stress is

A: Given; Determine the yield stress ? using Von Mises criterion,In a metal forming operation when the…

Q: what are t three components of shear strain?

A: shear strain is defined at point is  εx=δuδx   εy=δvδy   γxy=δvδx+δuδy

Q: In order to calculate the shear strain, the angle of twist should be in radian:

A: In the given statement it is asked wheather the unit of angle of twist is radian.

Q: The ratio of Engineering Stress and Engineering Strain is known as ______?

A: GIVEN DATA - A FILL IN BLANK IS GIVEN ABOUT STRESS AND STRAIN WE HAVE TO FILL CORRECT ANSWER

Q: What is Normal Stress?

A: Normal Stress: When the stress is acting in the direction perpendicular to the body then it is said…