Why do the Ductile materials fail in shear?

Q: What is torsional stress?

A: When the twisting load is applied over the body or a shaft, then the shear stress generated is…

Q: Distinguish between simple and indirect shear stress?

A: Simple shear stress also known as direct shear stress is the shear stress developed due to a…

Q: Why single shear strength is greater than double shear?

A:

Q: Why is it important to find the absolute maximum shear stress in the material when it is subjected…

A: Shear stress: It is the force imposed per unit area in a body that cause deformation of a material…

Q: 3. Why single shear strength is greater than double shear?

A:

Q: Describe the strain and energy?

A: When a body is subjected to any tensile or compressive forces then the body undergoes deformation…

Q: When a material is subjected to repeated stresses it will not fail without any prior indications.

A: When we apply repeated load on a material, then the properties or strength of the material will…

Q: • Calculate the factor of safety of the material under maximum shear stress and maximum distortion…

A:

Q: What happens if the principal stresses at a critical point in the material?

A: First, define the critical point. Critical points are those points in the given plane where the…

Q: 5-in stress strain curve the engineering stress will decrease after the tensile strength point?

A: Given data  To draw the stress strain diagram.

Q: Define the term Stress Concentrations?

A: Stress concentration is a location in a member under load where the magnitude of stress is…

Q: What is Longitudinal Stress?

A: The stress produced along the length of an object due to the presence of forces which are equal and…

Q: Part 2 As the area under the stress-strain curve decreases, the toughness___________.   stays the…

A: Toughness: The capacity to absorb the energy of the material before the failure is known as…

Q: Give an example of the single shear failure?

A: Shear is caused by the action of two opposite and equal forces acting on a material. If the two…

Q: 1. If failure occurs in tension, why is shear important? Why is torsional load called pure shear?

A: Solution:

Q: How can the ductility of material be specified?

A: Ductility is the material’s property to undergo large plastic deformation (permanent type) after the…

Q: The ability of a material to undergo large permanent deformation with the application of a tensile…

A: Elasticity: It is the ability of the material which allows to return to its original shape and size…

Q: How can we calculate the maximum stress?

A: Stress: Stress is defined as the developed force in the specimen per unit area when that specimen is…

Q: When can the shear stress be determined from the torsion formula?

A: Let a solid circular shaft fixed at one end is applied with an external torque. There will be…

Q: What type of stress is referred to as Ultimate Stress?

A: When a specimen is loaded axially with tension, it elongates. There is a point up to which if the…

Q: What is yield stress?

A: Yield Stress:  It is the amount of stress at the yield point of a material/component. The yield…

Q: The formula for Critically Resolved Shear Stress is

A:

Q: What is the Shear Stress Distribution?

A: Shear stress Shear stress is generated when a body deforms, but the applied force is parallel to the…

Q: When a material does not have a definitive proportional limit, then how is the modulus of elasticity…

A: The above question is based on the material that does not have a definitive proportional limit, i.e…

Q: 11. List the conditions that can induce brittle failure even in a ductile material.

A: Conditions that can induce brittle failure even in a ductile material- 1. High Strength Material are…

Q: How are the Normal and Shear Stress Components used?

A: Normal stress is defined as stress which induced due to the outside force acting normally on a…

Q: What is Ultimate stress?

A: Ultimate Stress The ultimate stress recognizes as the maximum value of stress that a material can…

Q: 5-In stress strain curve the engineering stress will decrease after the tensile strength point?

A: To give proper explanation of the above statement.

Q: Using the shear formula, how can we check to see that the allowable shear stress is not exceeded?

A: Shear stress acts parallel to the area of cross section of the member. Its magnitude at the outer…

Q: uess wh

A: given: engineering and true stress strain curve for shear are similar guess why

Q: force of 1100 KN is applied to punch a 40-mm-diameter hole in a plate. If the shear strength is…

A:

Q: Q12. How would a creep profile on a brittle material looks like?

A: How would be creep profile on a brittle material.

Q: 4. Why is modulus a characteristic property but not yield strength.

A: The Young modulus, also known as the modulus of elasticity in tension or compression (i.e., negative…

Q: Can the Shear stres also occur during axial loading?

A:

Q: What is plane stress?

A: Let us consider a plate in x-y plane  stress=σxτxyτxzτyxσyτyzτzxτzyσzPlane stress = σxτxy0τyxσy0000

Q: What is shear strength & how is it calculated?

A: There are no standard values published in the books for the shear strength. In some cases we take 60…

Q: .04. (a). Draw stress-strain diagram for mild steal. Hooke's law is applicable for what type of…

A: Hooke's law states that with in the elastic limit in object stress is directly proportional to…

Q: 6) Chapter 3: Problem 3.7: (USCS Units) The flow curve for a certain metal has a strain-hardening…

A:

Q: List 3 of the design methods that can be applied to avoid the occurrence of fatigue

A: Fatigue is the beginning and spread of fractures in a material as a result of cyclic stress,…

Q: Why does the shear center always lie on an axis of symmetry of a member?

A: Shear center can be defined as the point that is positioned on a beam where the load applied on it…

Q: Define Tensile strength.

A: Given Data⇒ Tensile strength Problem statement⇒ Problem says Define Tensile strength.

Q: - Why single shear strength is greater than double shear?

A: Given data Why single shear strength is greater than double shear strength

Q: How can the Maximum In-Plane Shear Stress determined?

A: The expression of the principal stress in a plane is given by,…

Q: What are the tensile forces?

A: Tensile force is the force applied on a material which stretches the material. The tensile force…

Q: a component is made of 6061 T6 aluminum sheet LT. A axial tensile stress of 50 ksi is applied at…

A: The deformation of a material in response to a tensile, compressive, or torsional force is…

Q: Using the shear formula, how can we check that the allowable shear stress is not exceeded?

A: given: Using the shear formula, how can we check that the allowable shear stress is not exceeded

Q: When an elastic material is subjected to normal stress, what would thestrains that are produced…

A: The strain is the response of a system to applied stress. When a material is loaded with a…

Q: Define the term material contracts?

A: The fundamental meaning of Material Contract is any contract ( except loan documents ) which can be…

Q: Normally when the creep is considered in materials?

A: given:  Normally when the creep is considered in materials?

Q: (Engineering and true stress-strain curves for shear are similar. Guess why?

A: Shear Rigidity: Too known as Modulus of Inflexibility, maybe a degree of material resistance…