5. (a) (b) (c) A coach driving shaft of 200 mm diameter is subjected to a torque of 126 kNm and a pure bending moment of 157 kNm. During inspection, a small surface crack is observed at 60° to the longitudinal axis of the shaft, as shown in Fig.Q6. Determine the normal and shear stresses at the crack as it passes through positions A, B and C during rotation of the shaft Display stress elements for points A, B and C on the outer surface Derive expressions for the principal stresses and determine principal stresses at A. B. and C

5. (a) (b) (c) A coach driving shaft of 200 mm diameter is subjected to a torque of 126 kNm and a pure bending moment of 157 kNm. During inspection, a small surface crack is observed at 60° to the longitudinal axis of the shaft, as shown in Fig.Q6. Determine the normal and shear stresses at the crack as it passes through positions A, B and C during rotation of the shaft Display stress elements for points A, B and C on the outer surface Derive expressions for the principal stresses and determine principal stresses at A. B. and C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum thin‐walled tube of hollow rectangular cross‐section, Figure 1,is subjected to a torque of magnitude, T = 15360 N.m. If the tube lengthis, L = 1 m , and the shear modulus of aluminum is, G = 28 GPa.1. Determine the total angle of twist of the one‐meter long tube.2. Determine the shear stresses on the walls of the tube cross‐section.Where does the maximum shear stress occur?
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
PART 1 My answer Ay=14.38 Cy=13.62 Part 2 Determine the shear force acting at each of the following locations: (a) x = 4.25- (i.e., just to the left of point B.) (b) x = 4.25+ (i.e., just to the right of point B.) (c) x = 9.25-(i.e., just to the left of point C) (d) x = 9.25+ (i.e., just to the right of point C) My Answer: (a) V= 14.38 kN (b) V= 14.38 kN (c) V= 14.38 kN (d) V= 28 kN Part 3 Determine the bending-moment acting at each of the following locations: (a) x = 4.25-(i.e.. just to the left of point B.) (b) x = 4.25+ (i.e.. just to the right of point B.) (c) x = 9.25 m (i.e., at support C) (d) x = 8.25 m My Answer: (a) M= 61.115kN-m (b) M= -148.885 kN-m (c) M= -76.985 kN-m (d) M= -91.365 kN-m Part 4: Use your bending-moment diagram to determine the maximum positive bending moment, Mmax, pos, and the maximum negative bending moment, Mmax, neg. Use the bending-moment sign convention detailed in Section 7.2. The maximum negative bending moment is the negative moment with…
A solid shaft of diameter 30 mm is fixed at one end. It is subjected to a tensile force of 10 kN and a torque of 60 Nm. At a point on the surface of the shaft, determine the principle stresses and the maximum shear stress.
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. a. At the MOST CRITICAL POINT of the sheet metal, calculate the stress state and sketch thecorresponding stress element b. If SAFETY FACTOR = 2 is considered, what is the MINIMUM shear force, V required tocut the sheet metal according to following criterions? i. ii. Tresca criterion?von Mises criterion? c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
-Define the maximum shear stress theory and sketch its failure envelope.-Define the maximum shear strain energy theory and sketch its failure envelope
The assembly shown consists of an aluminum shell (Ea = 70 GPa, αa = 23.6 × 10−6/°C) fully bonded to a steel core (Es = 200 GPa, αs = 11.7 × 10−6/°C) and the assembly is unstressed at a temperature of 20°C. Considering only axial deformations, determine the stress in the aluminum when the temperature reaches 185°C. The stress in the aluminum is − _____ MPa.
What happens when the in-plane principal stresses are of opposite signs?
Is the axial stress generally smaller than the stress developed by shear?
For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point.
Using the shear formula, how can we check to see that the allowable shear stress is not exceeded?