5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in the given figure. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of S mm, or the following stresses: 120 MPa in the steel, 90 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Ea = 70 GPa, and Ear = 83 GPa. Bronze Steel A = 480 mm A = 650 mm Aluminum A = 320 mm 3P 2P 2.0 m

5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in the given figure. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of S mm, or the following stresses: 120 MPa in the steel, 90 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Ea = 70 GPa, and Ear = 83 GPa. Bronze Steel A = 480 mm A = 650 mm Aluminum A = 320 mm 3P 2P 2.0 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The beam is loaded by two point forces P. The beam is assembled according to the cross-sectional view by nailing wooden parts with cross-sections of 50 mm x c = 220 mm and 25 mm x d = 260 mm. How large can the value of the load P be when the distance between the nails in the longitudinal direction of the beam is 100 mm, the cross-sectional area of the nail is 9 mm2 and their permissible shear stress is 110MPa? Then calculate the maximum stresses and shear stresses of the beam at that load when the distance between the articulated supports is L = 1.9 m and the length of the beam projections a = 1.3 m. Permissible shear force of one nail? kN Static torque of the cutting surface? mm^3 Maximum torque change in cantilever? kNm Cutting force of the projection? kN Magnitude of force P? kN Calculated with the obtained force P maximum normal stress? MPa shear stress maximum? MPa
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
Q#5: The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 10⁰ to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note : Use R=980 For Details See Picture Attached
Twelve Which of the following is a deformation? Select one: a. Tension b. Shear c. Compression d. Strain
Determine the a.Stress at 167 kN loadin MPa b.Strain at 167 kN loadin mm/mm(expressed in scientific notation) c.Modulus of elasticityMPa d.Modulus of resiliencein N-mm/mm3 e.Modulus of toughnessin N-mm/mm3
A steel rod of 15- mm diameter is held snugly (but without any initial stresses) between rigid walls by the arrangement shown in the figure part (a). (For the steel rod, use α = 12 x 10-6/˚C and E = 200 GPa.) Calculate the temperature drop ΔT (degrees Celsius) at which the average shear stress in the 12 – mm diameter bolt becomes 45 MPa. Also, what is the normal stress in the rod? What are the average bearing stresses in the bolt and clevis at A and between the washer (dW = 20mm) and wall (t = 18 mm) at B? If the connection to the wall at B is changed to an end plate with two bolts (see figure part b), what is the required diameter db of each bolt if the temperature drop is ΔT = 38˚C and the allowable bolt stress is 90 MPa?
Sketch the idealized stress-strain curve for A36 Steel. Label and provide the appropriate values for Fy, Fu, E and ey, and eu. Note: Use the “rule of thumb” that eu =200ey . Explain in detail what each value physically represents in the material.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?