Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa? 2P Bronze Aluminum A=400 mm² A = 600 mm² 4P -3m- +++ -5m P4 Steel A=300mm² 4m- 3P

Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa? 2P Bronze Aluminum A=400 mm² A = 600 mm² 4P -3m- +++ -5m P4 Steel A=300mm² 4m- 3P

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
A rod with a cross-sectional area of 0.5 in2 is composed of three sections: steel, aluminum, and bronze rigidly attached with each other, aluminum being at the center of the three. Axial loads are applied as follows: 12,000 lbs. going out of steel and 3000 lbs. going out of aluminum. Dtermine the stress in steel, aluminum, and bronze respectively. Draw the free-diagram.
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
A thin cylinder of length 2.5m and diameter 1.0 m is made from 3mm steel plates. Ifa gas is filled in the cylinder at a pressure of 750 kN/m2(gauge). Take E = 210 GPaand ν = 0.3 for steel, determine(i) the hoop stress and longitudinal stress in the wall of the cylinder(ii) the maximum shear stress in the plane of above two stresses(iii) change in diameter of cylinder due to the internal pressure of gas(iv) change in of the cylinder(v) change in volume of the cylinder
The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. and a modulus of elasticity ??? = 10,000 ??? and ?????? = 29,000 ???. The allowable stress of aluminum is 7.8 ksi and steel is 1.7 ksi. If the bar initially vertical,a. Determine the maximum P that can be applied.b. Determine the deformation of steel.c. Determine the deformation of aluminum.
An aluminum alloy cylinder (2) is clamped between rigid heads by two steel bolts (1), as shown. The steel [E = 200 GPa; α1 = 11.7 × 10−6/°C] bolts have a diameter of 19 mm. The aluminum alloy [E = 70 GPa; α2 = 23.6 × 10−6/°C] cylinder has an outside diameter of 160 mm and a wall thickness of 9 mm. Assume that a = 700 mm, b = 810 mm, and c = 325 mm. If the temperature of this assembly changes by ΔT = 60°C, determine(a) the normal stress in the aluminum cylinder.(b) the normal strain in the aluminum cylinder.(c) the normal strain in the steel bolts.
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
Value of P1=9 kNP2=105 kNP3=89 kNd=159 mm Strength of Materials
Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected between steel and bronze segments. If P = 25 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.