SIMPLE STRESSES340 mm1. Two plates areconnected by bolts asshown in the figure.Compute the bearingstress in each bolt.F 150 mmForce "F" is equal toF200 KN. The diameterof each bolt is 20 mm.50 mm340 mm

To determine the bearing stress in each bolt. Given, Diameter of each bolt (d) = 20 mm Magnitude…

SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bearing stress in each bolt. Force “F" is equal to 200 KN. The diameter of each bolt is 20 mm. F ► F 150 mm F - 50 mm 340 mm

SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the bearing stress in each bolt. Force “F" is equal to 200 KN. The diameter of each bolt is 20 mm. F ► F 150 mm F - 50 mm 340 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the effective depth of the section in PART A in mm.0 Use 3 decimal places in all your computations except for strain and rho(5 decimal places).
c. Calculate "P" in KN considering failure on bearing on projected area. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A flat brass bar has length L, constant thicknesst, and a rectangular cross section whose widthvaries linearly between b2 at the fixed support to b1at the free end (see figure). Assume that the taper ofthe bar is small. The bar has modulus of elasticity E.Calculate the displacements δB and δC if P = 200 kN,L = 2 m, t = 20 mm, b1 = 100 mm, b2 =115 mm,and E = 96 GPa.
A 16 inch square tied column cross- section with 8-#8 bars, three in each face to resist factored loads and moments of Pu = 250 kips and Mux = 55 kip-ft, and Muy = 110 kip-ft. Use fy = 60 ksi and f’c = 4 ksi. What is the value of φPn in kips using Bresler Equation. Use two decimal places
Given F1=14kips, F2=31kips, F3=92 kips and F4=41 kips with x=4 feet and y=9 feet. Calculate the member force in member EL in kips . Express your answer in 2 decimal places. Affix negative sign (-) if the member is in compression. Figure not drawn into scale.
Draw the Normal Force (N), Shear Force (T) and Bending Moment (M) diagrams of the beam whose loading condition is given in the figure. H=3ton , M=16tm, q1= 15t/m ,q2= 8t/m ,P=10ton ,a=8meter
Given a 2.2meter Wide Flange steel compression member with A=4851mm2, Ix=83069765mm4 and Iy=3563198mm4 with Fy = 345MPa. Calculate the design strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.201 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=19 kips, Q=13 kips, L1=7 ft, L2=9 ft, and L3=9 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.27 in2. Find the vertical displacement (in inches and absolute value) of point C caused by the 2448-lb load if x = 9.5 ft and θ = 41.7ᵒ. Use E = 29147 ksi for steel. Note: Round off the final answer to four decimal places.
NEED HELP ASAP PLEASE!!! A horizontal shelf AD of length L = 740 mm, width b = 360 mm, and thickness t = 30 mm is supported by brackets at B and C [see part (a) of the figure]. The brackets are adjustable and may be placed in any desired positions between the ends of the shelf. A uniform load of intensity q. which includes the weight of the shelf itself, acts on the shelf [see part (b) of the figure]. A L (a) D L (b) Determine the maximum permissible value of the load if the allowable bending stress in the shelf is Oallow = 7.5 MPa and the position of the supports is adjusted for maximum load-carrying capacity. Round to two decimal places. qmax kN/m
The compound shaft shown is attached to a rigid supports. For bronze segment AB, the diameter is 75 mm, maximum shearing stress is 60 MPa, and G = 35 GN/m^2. For steel segment BC, the diameter is 50 mm, maximum shearing stress is 80 MPa, and G = 83 GN/m^2.1. Which of the following most nearly gives the ratio torque carried by bronze to torque carried by steel? a. 1.2b. 1.8c. 1.6d. 2.02. Which of the following most nearly gives the torque carried by the bronze in kN.m?a. 4.98b. 9.15c. 6.53d. 3.143. Which of the following most nearly gives the maximum torque T than can be applied in kN.m? a. 6.4b. 5.1c. 4.3d. 7.8
Determine the smallest diameter (mm) that can be used in the clevis shown in the figure below if P = 421 kN. The shearing stress of the bolt is 305 MPa. Final answer should have 2 decimal places.