5. A cyclone separator in figure below is used to remove fine solid particles, such as fly ash, that are suspended in a gas stream. In the flue-gas system of an electrical power plant, the weight fraction of fly ash in the exhaust gases is approximately 0.001. Determine the mass flow rates at the two outlets (flue gas and fly ash) when 10 kg/s of flue gas and ash mixture enters this unit. Also determine the amount of fly ash collected per year. Flu gas Flue gas and ash- Ash

5. A cyclone separator in figure below is used to remove fine solid particles, such as fly ash, that are suspended in a gas stream. In the flue-gas system of an electrical power plant, the weight fraction of fly ash in the exhaust gases is approximately 0.001. Determine the mass flow rates at the two outlets (flue gas and fly ash) when 10 kg/s of flue gas and ash mixture enters this unit. Also determine the amount of fly ash collected per year. Flu gas Flue gas and ash- Ash

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a steam generator, a dry steam of (14 bar) enters the superheater which increase the steam temperature by (65 C) and reduce the flue gases temperature by (100 C°). Calculate the flue gases mass flow rate per (1 kg/s) of steam flow rate, if the specific heat capacity of the flue gases is (1.005 kj/kg.K).
Water flows through a horizontal coil heated by steam condenaing on the outside. If the inlet pressure and temperatire are 2 atm and 160°F (state 1) and at the exit 1 atm and 220 °F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity is 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 Btu/lb, H2=1154.4 Btu/lbA. 1031 Btu/lbB. 1042 Btu/lbC. 1048 Btu/lbD. 1052 Btu/lb
Using that information and this table For the average monthly rate of geothermal heat available, determine, for the real case: in a tabular format and show sample calculation for one month. the necessary monthly average mass flow rate (in kg/s) of the refrigerant that must be pumped through the heat exchanger to collect the thermal energy from the available geothermal hot water flow rate if the hot water was cooled by 5°C. What should be the flow capacity (in kg/s) of feed pump of the ORC heat engine that you are designing and the monthly average net electric power generation capacity (in kW). 2. the monthly average net electric power generation capacity (in kW) and yearly average net electrical power generation capacity (in kW).
The air considered as the ideal gas flows through the compressor and heat exchanger at a volumetric flow rate of 26.91 m3 / min as shown in the figure. At the same time, a stream of liquid water passes through the heat exchanger. The information given in the figure is for continuous flow. Considering the compressor and heat exchanger as adiabatic and ignoring kinetic and potential energy changes, a) the power requirement of the compressor (kW) and the mass flow rate of the cooling water (kg / h),b) Calculate the entropy generation (kW / K) per unit time for the compressor and heat exchanger.
Hot air at 400°C and 150 kPa is to be used to produce saturated steam at 200°C in an insulated, non-mixing heat exchanger. Water enters the heat exchanger at 20°C while the air leaves at 350°C. The mass flow rate of air is 0.8 kg/s, pressure drops are negligible, and specific heats for air are evaluated at the average air temperature.What is the mass flow rate of water, in kg/s. Report your answer to four decimal places using rounding.
Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 196 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K), keeping three decimal places.
Please Help,will provide helpful e Ratings for correct solution. Thank You. Water flows through a horizontal coil through which high-temperature flue gas passes. As water passes through the coil, it passes from the liquid phase at 200 kPa and 80°C to the vapor phase at 100 kPa and 125°C. The entry speed of water into the coil is 3 m/s and the exit speed of steam is 200 m/s. Calculate the heat transferred per unit mass of water through the coil? The enthalpies of the inlet and outlet streams are given as 334.9 kJ/kg and 2726.5 kJ/kg, respectively.
Steam at a pressure of 20 bar and a temperature of 300 oC flows in a pipe at a mass flow rate of 2 kg/s is throttled to a pressure of 8 bar before entering a mixing venturi to mix with another supply of steam at 8 bar and a dryness fraction of 0.9 with a mass flow rate of 5 kg/s. Sketch a diagram showing the arrangement and calculate the quality of the steam at the exit of the venturi after mixing.Calculate the internal diameter of the pipe to transport the steam before the throttle valve if its velocity is limited to 15 m/s.
Air at a static temperature and pressure of 9°C and 100 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 206 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K)
A 1000 litre containment tank catches the outflow from a processing apparatus which has 800 litres of water with 2g of chemical agent dissolved in it. Additional supply comes into the tank at 3 litres/hr containing 5 g/litre of the chemical agent. The solution leaves the containment tank at 3 litres/hr. When the amount of chemical agent in the containment tank reaches 500 g, no more supply is allowed to enter the system. Instead,fresh water is input into the tank at 2 litres/hr; and at the same time,the outflow is increased to 4 litres/hr. How much chemical agentis held in the containment tank at any time t.Assume all liquids are well-mixed.
P23. Steam enters an insulated nozzle with negligible velocity, 200 psi and 500°F. Steam exits at 100 psi and 400°F.For steady-state operation and neglecting potential energy effects, determine the velocity of the steamleaving the nozzle in ft/s.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.