5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow blocksand form into a plinth. It has a specific weight of 4.42 metric slug/ft with a specific gravity of 3.Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in psi.r= 304.8 mmR = 457.2 mmMid-height= 1219.2 mmh = 2438.4 mmH

Question is based on plinth made up concrete hollow blocks with shape of frustum of cone . Specific…

5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow block and form into a plinth. It has a specific weight of 4.42 metric slug/ft³ with a specific gravity of 3 Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in ps r = 304.8 mm R = 457.2 mm Mid-height = 1219.2 mm %3D h = 2438.4 mm H

5. A plinth with a shape of a frustum of a cone is made of a melted CHB or Concrete hollow block and form into a plinth. It has a specific weight of 4.42 metric slug/ft³ with a specific gravity of 3 Assuming it is at rest find the average normal stress acting in the mid-height of the plinth in ps r = 304.8 mm R = 457.2 mm Mid-height = 1219.2 mm %3D h = 2438.4 mm H

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
Due to the application of line loads q1 and q2, the vertical stress increase, ∆?? , at point A is 42 kN/m2 . Determine
A rectangular concrete slab, 3 m x 4.5 m, rests on the surface of a soil mass. The load on the slab is 2025 kN. Determine the vertical stress increase in kPa at a depth of 3 m under the center of the slab. a. 102.4 b. 63 c. 13.5 d. 47.4
knowing that P = 18 Kips, determine the maximum stress when r = 0.45 in and r = 0.70 in
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
Q#5: From the Tri –axial test, determine the effective normal stress on the plane of Maximum shear stress. Explain why the shear failure occurred along the plane with angle 54.73 and not along the plane of maximum shear stress. Take σ’1 = 552, σ’3 = 276, ø’ = 19.45? Find σ’ = ? τf = ? τ: ?
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A, = 3050 mm? and an allowable normal stress of 65 MPa. Bar (2) has a cross-sectional area of A2 = 3000 mm? and an allowable normal stress of 65 MPa. Assume x1 = 1.8 m. x2 = 2.7 m. y1 = 1.0 m, and y2 = 2.8 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
A solid circular pole is subjected to linearly varying distributed force with maximum intensity o at the base and an axial compressive load P at the top (see figure). Find the required diameter d of the pole if the maximum allowable normal stress is 150 MPa. Let go = 6.5 kN/m, P = 70 kN, and L = 3 m.
A rectangular concrete slab, 3 m x 4.5 m, rests on the surface of a soil mass. The load on the slab is 2025 kN. Determine the vertical stress increase in kPa at a depth of 3 m at the distance of 1.5m from the lower corner point between the right edge and the bottom edge. a. 63 b. 47.4 c. 13.5 d. 102.4
Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontal plane.
The circular flexible area uniformly loaded (q=320KN/m^2). Determine the change in vertical stress: (a) at point A. (b) at a point 2m below point A