Axial loads are applied to rigid bearing plates in a system of steel bars. The cross-sectional area of bar (2) is 270 mm². Determine the magnitude of the normal stress in bar (2). 90 kN 50 kN 50 kN (3) rigid bearing plates 75 kN 21 75 kN 40 kN 40 kN (1)

Axial loads are applied to rigid bearing plates in a system of steel bars. The cross-sectional area of bar (2) is 270 mm². Determine the magnitude of the normal stress in bar (2). 90 kN 50 kN 50 kN (3) rigid bearing plates 75 kN 21 75 kN 40 kN 40 kN (1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that ? = 200??, determine (a) the shearing stress in each rivet, (b) the bearing stress in each plate 25mm thick and 100mm wide. Assume that the axial load ? is distributed equally among the 6 rivets, and the diameter of hole is 22mm.
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.
A steel plate 2.5 m x 1.6 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the shear stress (MPa) in the 16 mm diameter pins through the clevis The correct answer is 45.33. Show solution.
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.41 from the support. (MPa) Properties: Beam width = 206 mmBeam height = 495 mmPu = 66.2 kNSpan of the beam = 11 mPrestressing force = 335 kNeccentricity = 105 mm
A simple wooden AB beam (see figure 2) supportsa uniform load of 24 kN / m (includes weightcharacteristic of the beam), with a length L = 1.75m and sectionrectangular cross section with width of 200mm and height250mm. Determine:a) Reactions and shear diagram.b) Using the maximum shear force, find theshear stress in:to. The centroid.b. At a distance of 62.5mm from the centroid.c. At the ends of the cross section.c) Draw the shear stress diagram withall values obtained.
an 8 m long steel is pinned at the top and fixed at the bottom. the column is provided with lateral support 3m from the top in the weak direction. the properties of the column section are as follows: ix = 178.1x10^6 mm^4 ly = 18.8x10^6 mm^4 a = 8129 mm^2 fy = 400 mpa a. what is the critical effective slenderness ratio? %3d %3d b. what is the buckling stress of the column? c. calculate the critical load pc in kn
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
Two steel [E=29,600 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in, and a wall thickness of 0.257 in. Pipe (2) has an outside diameter of 4.250 in. and a wall thickness of 0.215 in. Assume L_{1} = 13ft and L_{2} = 18fi . If the normal stress in each steel pipe must be limited to 23 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
A cantilever beam of IPN 300 section and length L=3m supports a slightly inclined load P=2,5KN at the free end (see Figure Q2).2.1 Plot a graph of the stress ?? at point A as a function of the angle of inclination ?. [16]2.2 Plot a graph of the angle ?, which locates the neutral axis n-n, as a function of the angle ?. See Table F-2 of Appendix F for the dimensions and properties of the beam (When plotting the graphs, let ? vary from 0 ?? 10°).