5. Air at stagnation pressure of 600 kpa and stagnation temperature of 530 K enters a frictionless convergent- divergent nozzle as shown in figure the throat area is 5cm2 and the exit area is 12.5 cm2, the back pressure is 300kpa, and normal shock occurs within the divergent section. Determine The back pressure if the flow were isentropic throughout Оa- 38kpa Ob- 48kpa Ос- 58kpa Od- 68kpa

5. Air at stagnation pressure of 600 kpa and stagnation temperature of 530 K enters a frictionless convergent- divergent nozzle as shown in figure the throat area is 5cm2 and the exit area is 12.5 cm2, the back pressure is 300kpa, and normal shock occurs within the divergent section. Determine The back pressure if the flow were isentropic throughout Оa- 38kpa Ob- 48kpa Ос- 58kpa Od- 68kpa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A normal shock produced by an explosion propagate at a constant velocity of 450 m/s into still air of 100 kPa and 23 °C. The ratio of stagnation pressure upstream the shock to stagnation pressure of the gas flow behind the wave is
Air flows isentropically in a converging-divergingnozzle with a throat area of 3 cm2. At section 1, the pressureis 101 kPa, the temperature is 300 K, and the velocityis 868 m/s. (a) Is the nozzle choked? Determine(b) A1 and (c) the mass flow. Suppose, without changingstagnation conditions or A1, the (flexible) throat isreduced to 2 cm2. Assuming shock-free flow, will therebe any change in the gas properties at section 1? If so,compute new p1, V1, and T1 and explain.
If there are no shock waves and the pressure at one ductsection in Fig. is 55.5 kPa, what is the velocity atthat section?(a) 166 m/s, (b) 232 m/s, (c) 554 m/s, (d ) 706 m/s,(e) 774 m/s
A gas at a specified stagnation temperature and pressure is accelerated to Ma = 2 in a converging–diverging nozzle and to Ma = 3 in another nozzle. What can you say about the pressures at the throats of these two nozzles
The reservoir pressure and temperature for a convergent-divergent nozzleare 5 atm and 520◦R, respectively. The flow is expanded isentropically tosupersonic speed at the nozzle exit. If the exit-to-throat area ratio is 2.193,calculate the following properties at the exit: Me, pe, Te, ρe, ue, p0,e, T0,e.
A Pitot tube inserted at the exit of a supersonic nozzle reads8.92 × 104 N/m2. If the reservoir pressure is 2.02 × 105 N/m2, calculatethe area ratio Ae/A∗ of the nozzle.
Using Bernoulli's principle, determine the pressure change between the upstream and downstream end of the nozzle. The velocities at the entrance and exit are 2.55m/s and 1.13m/s,respectively. Note: Temperature is 20 degrees centigrade. Nozzle is horizontal.
A converging nozzle having an exit diameter of 30 mmmm is connected to the large tank (Figure 1). The absolute pressure outside the tank is 102 kPakPa. Figure 1 of 1 Part A If the temperature of the air in the tank is 20∘C∘C and the absolute pressure is 280 kPakPa, determine the mass flow from the tank.
Air enters a converging–diverging nozzle at a pressure of 1200 kPa with negligible velocity. What is the lowest pressure that can be obtained at the throat of the nozzle?
A supply tank at 500 kPa and 400 K feeds air to a converging–diverging nozzle whose throat area is 9 cm2. The exit areais 46 cm2. State the conditions in the nozzle if the pressureoutside the exit plane is (a) 400 kPa, (b) 120 kPa, and (c) 9kPa. (d ) In each of these cases, fi nd the mass fl ow.
A converging nozzle having an exit diameter of 30 mmmm is connected to the large tank (Figure 1). The absolute pressure outside the tank is 102 kPakPa. If the temperature of the air in the tank is 20∘C∘C and the absolute pressure is 480 kPakPa, determine the mass flow from the tank. Express your answer using three significant figures.
The converging-diverging flow domain is shown in Figure 1. The inlet diameter is 0.2 m, the throat diameter is 0.15 m, and the outlet diameter is 0.24 m. The axial distance from the inlet to the throat is 0.30 m—the same as the axial distance from the throat to the outlet. At the inlet section, the stagnation pressure P0 is set to 220 kPa (absolute), while the stagnation temperature T0, at the inlet is set to 300 K.