Please answer in typing format 5. During the blocked rotor test, a six-pole, 60 H, 3-phase induction motor takes 200A andconsumes 80 kW. If r₁ =r2. Find out the starting torque.

Step 1:pole = 6In block rotor test the wattmeter indicates only the copper loss…

Answered: 5. During the blocked rotor test, a…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

Name three factors that determine the torque produced by an induction motor.
Induction motors and welding transformers require magnetizing current, which causes a. lagging power factor. b. leading power factor. c. unity power factor. d. zero power factor.
What are the advantages and disadvantages of using the following types of motors? shaded-pole motor PSC motor split-phase motor capacitor-start–capacitor-run motor
A 460V, 25hp, 60Hz, 4 pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1 = 0.641 Ω R2 = 0.332 Ω X1 = 1.106 Ω X2 = 0.436 Ω Xm = 26.3 Ω The total rotational losses are 1100W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 3.5% at the rated voltage and rated frequency, find the motor’s Speed Stator current Power factor Pconv and Pout Ʈǐnd and Ʈload Efficiency
A 3-phase, 6 pole, 440 V, 60 Hz, Y-connected induction motor has the following impedances per phase referred to the stator circuit: R1=0.43 Ω, R2=0.54 Ω, X1=1.263 Ω, X2=0.608 Ω, XM=43Ω The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2 percent at the rated voltage and rated frequency, Find the motor speed, stator current, output power
Q11-b) A three-phase induction motor is used to drive many types of loads for example water pump and compressor. Explain the followings: i. The construction and its operational principle;ii. Synchronous speed, rotor speed, slip and their relationships,iii. Starting methods for induction motor,iv. Disadvantages of induction motor.
A 440-V, 60-Hz, 2-pole, Y-connected, three-phase induction motor has the following parameters in ohms/phase: R1 = 0.3, X1 = 0.9, R2 = 0.6, X2 = 0.9, Rc = 150, Xm = 60. If the rotational loss is 4% of the powerdeveloped, determine the efficiency of the motor when it runs at 4% slip.
A certain four-pole 240-V-rms 60-Hz delta-connected three-phase induction motor has Rs=1 ΩRr′=0.5 Ω Xs=1.5 ΩXr′=0.8 Ω Xm=40 Ω Neglecting losses, find the starting torque and starting line current for the motor.
A three-phase induction motor with electrical phase equivalent circuit below is 4 poles and the label rotor speed It is 1455 rpm. Wind-friction and iron losses are neglected. The motor is delta connected. a.) Calculate the development moment. b.) Calculate the overturning moment. c.) Calculate the value of the line current at the stator development moment (t = 0 s). d.) If Y / ∆ is started to this motor, what will be the value of the line current at the moment of development (t = 0 s).
A single- stack, 3- phase VR motor has a step angle of 20° Find . the number of its rotor and stator poles?
A Y-connected squirrel cage 3-phase induction motor has the following parameters: 480V, 50 Hz, 4-pole, 1320 rpm, Rs= 2.4 Ohm, Rr’=2.9 Ohm, Xs=Xr’=3.3 Ohm, Xm=65 Ohm. It is controlled by a VSI with (V/F=const.). Calculate motor max. torque, for a frequency of 100Hz.
The power input to a 500V, 50Hz, 6 pole, 3 phase squirrel cage induction motor running at975 RPM is 40kW. The stator losses are 1kW and friction and windage losses are 2kW.Find the output power of the motor.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

5. During the blocked rotor test, a six-pole, 60 H, 3-phase induction motor takes 200A and consumes 80 kW. If r₁ =r2. Find out the starting torque.