5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration & (both counterclockwise). 7) if w = 5.4 rad/s and α = 7.8 rad/s², length | = 2.1 m, and angle = 30°, what is the linear acceleration of collar B in m/s²? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is to the left. Your answer must include 2 places after the decimal point. B Your Answer: 0 0.5 m ω, α

5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration & (both counterclockwise). 7) if w = 5.4 rad/s and α = 7.8 rad/s², length | = 2.1 m, and angle = 30°, what is the linear acceleration of collar B in m/s²? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is to the left. Your answer must include 2 places after the decimal point. B Your Answer: 0 0.5 m ω, α

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B.
find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
The figure is made of rigid members AB, BC, DE, and EF, whichare pinned at A, B, D, E, and F. End C of member BC is pinned to a block which slides on member DE. For the given position, angular velocity of member AB = 2 rad per sec clockwise and angular acceleration of member AB = 3 rad / s^2 counterclockwise. Find the linear velocity and acceleration of the block at C for this position.
q2a = 8in ; q3b = 4in ; q2q5 =3.75in. the crank q2a rotates uniformly cw at a speed of 90 rpm. find the absolute linear acceleration of point b
In the given figure, A link OB is rotating with a constant angular velocity of 2 rad/s in counter clockwise direction and there is a block is sliding radially outward on it with an uniform velocity of 0.75 m/s with respect to the rod, If OA = 1m , find the magnitude of the absolute acceleration of the block at location A ?
A 3 in radius disk spins at the constant ω1 - 5 radian/s and a constant rate ω2= 4 radians/s. If the angle is 45 degrees, find the absolute acceleration at point P.
In the mechanism shown below, link AB rotates at a constant angular velocity of 1.5 rad per sec counterclockwise. What is the acceleration of C along the channel? Assume the positive direction to be upwards and to the right.
At the image below, what is the rotation of rod AB about point A if piston b moves to the right? Moreover, what is the magnitude of the acceleration of end a if velocity of end A is 7.5 m/s upward and is increasing at a constate rate of 18.75 m/s^2?
The crank of a slider crank mechanism rotates clockwise at a constant speed of 300 r.p.m. The crank is 150 mm and the connecting rod is 600 mm long. Using vector diagrams, Determine: a). Linear velocity and acceleration of the midpoint of the connecting rod. b). Angular velocity and angular acceleration of the connecting rod, at a crank angle of 45 from inner dead centre position. c). Using trigonometry, confirm your results for the velocity and acceleration in parts (a) and (b).
The figure shows a right-angled construction frame ABC. When measured at rest, it has dimensions as follows: AB = 18.9 m, AC = 10.0 m, and BC = 16.0 m. This frame is now given a new velocity of 0.420 c, relative to Earth, in a direction parallel to AC. How long is part BC of this frame with the new velocity as measured by Earth-based engineers?
In the figure shown, the pivoted right link AB carries a pin P whose position is controlled by horizontal slotted bar. At the instant that y=2in, the slotted bar is moving upward at a constant velocity of 4 ips. What is then the x-components of the velocity and acceleration of the pin P?
(The complete question is in the picture) A disk rotates with constant angular acceleration about an axis passing through its center of mass. At an instant, its angular speed is measured to be 20.0 [rad/s]. What is the angular speed of the disk after 2.00 [s] if it has revolved by 60.0 [rad] during this timeinterval? A. 10.0 [rad/s]B. 20.0 [rad/s]C. 30.0 [rad/s]D. 40.0 [rad/s]