5. The characteristic equation of a feedback control system is s'+Ks+9s+18. When the system is marginally stable, the frequency of the sustained oscillation: a) 1 b) 1.414 c) 1.732 d) 3 6. The characteristic equation of a system is given as s3+25s2+10s+50-0. What is the number of the roots in the right half s-plane and the imaginary axis respectively? a) 1,1 b) 0,0 c) 2,1 d) 1,2

5. The characteristic equation of a feedback control system is s'+Ks+9s+18. When the system is marginally stable, the frequency of the sustained oscillation: a) 1 b) 1.414 c) 1.732 d) 3 6. The characteristic equation of a system is given as s3+25s2+10s+50-0. What is the number of the roots in the right half s-plane and the imaginary axis respectively? a) 1,1 b) 0,0 c) 2,1 d) 1,2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

the unity negative feedback controller shown below, in whichR(s) = thetades(s) is the desired pitch angle, H(s) is the transfer function computed in part (a), and C(s) =K(s+1)/s, a proportional-integral (PI) controller with a single control gain K. (a) Suppose that you want the pitch angle to increase at a constant acceleration of 1 deg/s2. Toachieve this, you set the desired pitch angle to a parabolic function, r(t) = 0.5t2 * us(t), where us(t) is the unit step function. What is the system type n? Calculate the steady-state error ess of the closed-loop system as a function of ?(b) Compute the closed-loop transfer function, Hcl(s) = Y(s)/R(s). Write the charateristic equation of the closed-loop system in the form 1 + KL(s) =0
CONTROL SYSTEMA negative unity-feedback control system has the forward path transfer function given as G (s)=(K/S^3+15s^2+50s)a) Draw the root locus diagram.b) Find the K value/value range that makes the system response overdamped.c) Find the K value/value range that makes the system response under damped.d) Find the K value/value range that makes the system response criticully damped.
Consider unity negative feedback applied to the system: G(s) = k/s(s^2+4s+5) (a) Give a complete sketch of the root locus (0 ≤ k ≤ ∞) for this system assuming a unity feedback configuration. Make sure you show all the significant features on your sketch. Give particular attention to the angle of departure from the complex poles. (b) Indicate on your root locus diagram the point at which the damping ratio of the dominant poles is 0.5.
Assume any finite duration discrete time signal x(n) following the necessary condition satisfying the property of energy signal of your own choice. Now consider a discrete time system whichperforms Amplitude scaling operation followed by time reversal operation based on y(n) = ax(n) + x(-n). Sketch the output of resultant signal. Now classify and justify your answer with necessary and sufficient conditions that whether the above system based on all types of system.
When a unit step input is applied to the closed-loop control of a system with G(s) function and controlled by proportional control, the system operates at the point A= -2.5+j3.57. A) For the relevant operating point, Calculate the proportional gain K. Find the value of ζ. Find the percent (%OS) overshoot Find the natural frequency of the point of interest. B) For the PD controller to be added when the same system is wanted to be operated at the point B= -7.8+j8.77, Find the controller zero value. Find the new K value. Find the ζ value of the relevant point. Find the percent (%OS) overshoot Find the natural frequency of the point of interest.
For a unity-feedback system with G(s) = K / s(s + 20)(s + 40) operating with a 20% overshoot, design a compensator to decrease the settling time by a factor of 2 without affecting the percent overshoot:i. Find the uncompensated system's dominant poles, gain, and settling time. ii. Find the compensated system's dominant poles and settling time. iii. Find the compensator's pole position and required gain. (Assume the compensator’s zero is at -20).
Control System , Given transfer function, T (s) = αs + β / s^2 + (α + 2)s + β (i) Pick a pair of values for parameters α and β such that the closed-loop system is stable (ii) Pick a pair of values for parameters α and β such that the closed-loop step response exhibitszero steady-state error. (iii) Pick a pair of values for parameters α and β such that the closed-loop step response isunderdamped, exhibiting a settling time of 4/5 seconds and a peak time of π/7 seconds.
Consider the unity-feedback control system with the following feedforward transfer function: G(s) = K / s(s2+4s+5) (1) Plot the root locus. (2) Determine closed-loop poles that have the damping ratio of 0.5. Find the gain value K at this point. (3) For what value of K is the overshoot less than 10% and the maximum rise time less than 1.5s.
Please find the following:(a) The error constants Kp, Kv and Ka and also the system type.(b) The range of K so that the steady-state error (i.e., e(t) = r(t) - c(t) as t -> ∞)under a unit ramp input is less than 0.01.(c) The range of K that keeps the system stable. (d) The value of K that makes the system oscillate and also the frequency ofoscillation. (e) Suppose that we replace the constant gain controller K with the moresophisticated PI controller, i.e., Gc(s) = K + (KI/s), find the range of thecontroller gains (K, KI) so the system is stable.
1-A unit feedback system has G(s) = 1/ 0.5s. Derive the time response (c(t)) of the system, when subjected to a step input signal. 2-A unit feedback system has G(s) = (5+3)/s(-2)(s+6). (a) Obtain the characteristic equation (b) Justify the stability of system.
A unity feedback system has the open loop function G(s)=1/3s3+2s2+0.6s+11 Using RH criterion, Write whether the system is stable or unstable. The system is : Answer
Ignoring the “zero” in the numerator, and based only on the denominator of the closed-looptransfer-function, determine the range of constants Kp and Ki such that the rise-time of theclosed-loop system is equal (or less than) ?r =0.18 s and so that the relative damping factor ζ isequal to (or greater than) 0.8. Use the textbook approximation for the rise-time.