5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your

5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.65P

See similar textbooks

Related questions

Q: During a high Reynolds number experiment, the total drag force acting on a spherical body of…

A: Given data, From stokes equation,

Q: Air flows across a 20-cm-square plate with a velocity of 5 my/s. Free-stream conditions are 10:C and…

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220°C flows in…

A: Given data: *The hot carbon dioxide is at 1 atm pressure. *The temperature of the gas is Tg=220°C.…

Q: Q8) A 0.4 W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a…

Q: A black 20-by-20-cm plate has air forced over it at a velocity of 2 m/s and a temperature of 0◦C.…

A: Given: The area of plate, A = 20x20 cm The velocity of air, v = 2 m/s The temperature of air, Ta =…

Q: Q3: Air flows across a 20-cm-square plate with a velocity of 5 m/s. Free-stream conditions are 10 C…

A: In general, there are three modes by which heat gets transferred from one place to another. The…

Q: An airplane engine intakes air. adds fuel to burn the air and exhausts the burnt gases to generate…

Q: What are the turbulence intensity differences on offshore and onshore?

A: Turbulence intensity differences on offshore and onshore ;

Q: Air at 1 atm and 20°C is flowing over the top surface of a 0.2 m x 0.5 m-thin metal foil. The air…

A: Given data: Air at 1 atm pressure and temperature,T∞=20°C, is flowing over a thin metal foil of…

Q: Water at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s.…

Q: What does the friction coefficient represent in flow over a flat plate? How is it related to the…

A: Drag force is a force acting on a body (moving or stationary)which is present in a moving or…

Q: A metallic airfoil of elliptical cross section has a mass of 50 kg, surface area of 12 m2, and a…

Q: Hot methane exhaust gas at 1 atm is being cooled by flat plates. The gas at 150°C flows parallel…

Q: Four power transistors, each dissipating 12 W, are mounted on a thin vertical aluminum plate (k =…

A: The properties of air at 40 degrees Celsius and 1 atm pressure are: The Reynolds number of the flow…

Q: It has a density of 5900 kg/m3 and a specific heat of 590J/kg.°C with a diameter of 15 cm. A…

Q: Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and…

A: Convection heat transfer is given as: Q=hAs(Ts-T∞) Where, h is convection heat transfer coefficient.…

Q: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a…

Q: Air at 300 degrees Celsius flows over a plate of dimension 0.5 m by 0.25 m. If the convection heat…

Q: What are the factors that affect the value of Friction factor in Laminar flow and Turbulent flow?

A: There are some factors on which friction factor depends :

Q: What is the physical significance of the Reynolds number? How is it defined for external flow over a…

A: Given: Plate with length L To find; Significance of Reynolds number Reynolds number for external…

Q: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C…

A: Determine the mean film temperature

Q: Engine oil at 83°C flows over the upper surface of a 5-m-long flat plate whose temperature is 18°C…

Q: A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a…

A: Given data Diameter of component = 0.3cm = 0.003m Length of the component = 1.8 cm = 0.018m Velocity…

Q: In the effort to increase the removal of heat from a hot surface at 120°C, a cylindrical pin fin (kf…

A: The properties of air at a temperature of 70 oC are given as, The characteristic length of the…

Q: A metallic airfoil of elliptical cross section has a mass of 50 kg, surface area of 12 m2, and a…

Q: Air at a temperature of 25oC flows parallel over a flat plate with free-stream velocity of 2 m/s.…

Q: During flow over a given body, the drag force, the upstream velocity, and the fluid density are…

A: Drag force is the resistive force exerted by a fluid due to its motion. Drag force is supposed to…

Q: Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40 C and. The plate…

Q: A 15 cm x 15 cm circuit board dissipating 15 W of power uniformly is cooled by air, which approaches…

A: The properties of air at 300 K are: (a) The value of Nusselt number at the leading is The film…

Q: A 1.2-in-outer-diameter pipe is to span across a river at a 140-ft-wide section while being…

A: Given data as per question Diameter of pipe =1.2 in Flow velocity = 10ft/s

Q: Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The…

A: Given data: The temperature of the air is T∞=25°C The surface temperature of the plate is Ts=150°C…

Q: 1) Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: Consider a refrigeration truck traveling at 70 mi/h at a location where the air is at 1 atm and…

A: Given that,

Q: Consider laminar flow over a flat plate. How does the local friction coefficient change with…

A: In the boundary layer flow of a fluid over any surface, the local friction coefficient represents a…

Q: Air is flowing in parallel over the upper surface of aflat plate with a length of 4 m. The first…

A: The properties of air at 30 degree Celsius are: The local Reynolds number can be calculated as,…

Q: Water at 25°C and 1 atm is flowing over a long flat plate with a velocity of 8 m/s. Determine the…

A: Given data T=25°cV=8 m/sRecr=5×105

Q: A 2m by 3m flat plate is suspended in a room, and is subjected to air flow parallel to its surfaces…

Q: What is lift? What causes it? Does wall shear contribute to the lift?

A: given: What is lift? What causes it? Does wall shear contribute to the lift?

Q: QUESTION 3 a) During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and…

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: Q2/Engine oil at 80°C flows over a 6-m-long flat plate whose temperature is 30°C with a velocity of…

Q: Air flows over a l-meter-wide flat plate at a constant velocity of 20 m/s and ambient conditions of…

Q: A 15-cm X 15-cm circuit board dissipating 15 W of power uniformly is cooled by air, which approaches…

A: According to the information we have a board that uniformly discharges 15 W of power is cooled at a…

Q: A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in…

A: Given:- Diameter of bottle=10cm height=30cm temp of cold water =3°C temp of air=27°C temp of water…

Question

A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30°C forced across it at a velocity of 50 m/s (h = 180 W/m² K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10°C. Comment on your calculation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a house. If the air outside is at 5°C and the surface temperature of the wall is12°C, determine the rate of heat loss from that wall by convection. What would your answer be if the wind velocity was doubled
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
A 5.0-cm-diameter cylinder is heated to a temperature of 200 oC, and air at 30 oC forced across it at a velocity of 50 m/s (h = 180 W/m2K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 oC. Comment on your calculation. COMPLETE SOLUTION
A 1.2-in-outer-diameter pipe is to span across a river at a 115-ft-wide section while being completely immersed in water. The average flow velocity of the water is 8 ft/s, and its temperature is 70°F. Determine the drag force exerted on the pipe by the river.
An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this heat is lost from the head and disregarding radiation, determine the average surface temperature of the head when it is not covered and is subjected to winds at 10°C and 25 km/h. The head can be approximated as a 30-cm-diameter sphere. Assume a surface temperature of 15°C for evaluation of ms. Is this a good assumption?
Q6: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C and exposed to atmospheric air at 4°C. Calculate the heat lost by the plate. Answers: Q=1907 W
A long 8-cm-diameter steam pipe whose external surface temperature is 90°C passes through some open area that is not protected against the winds. Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 7°C and the wind is blowing across the pipe at a velocity of 50 km/h.
A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in windy air at 27°C. The water temperature is measured to be 11°C after 45 min of cooling. Disregarding radiation effects and heat transfer from the top and bottom surfaces, estimate the average wind velocity.
Calculate the heat transfer from a 60 cm x 60 cm plate on which air flows at 40 C and. The plate temperature is 100 C while the air speed is 5 m/s.
A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some open area that is not protected against the winds . Determine the rate of heat loss from the pipe per unit of its length when the air is at 1 atm pressure and 10°C and the wind is blowing across the pipe at a velocity of 8 m/s.
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
Ethylene glycol at 40°C flows over a heated plate very wide, 6 m long, at velocity of 0.04 m/s. For a temperature = 90°C, determine: 1- the thickness of the hydrodynamic boundary layer at the end of the plate2- the thickness of the thermal boundary layer at the end of the plate3- the local and average heat transfer coefficient at the end of the plate4- the total heat flux transferred from the heated surface.