50 It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d.pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor -0.003, estimate the rate of flow and the power to be supplied to the pump assuming n=0.5. 2 Q (m/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0

50 It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d.pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor -0.003, estimate the rate of flow and the power to be supplied to the pump assuming n=0.5. 2 Q (m/s) 0.0028 0.0039 0.005 0.0056 0.0059 Ah (m) 23.2 21.3 18.9 15.2 11.0

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter13: Energy And Power

Section: Chapter Questions

Problem 3P: An elevator has a rated capacity of 2200 lb. It can transport people at the rated capacity between...

See similar textbooks

Similar questions

Water at 10°C flows at the rate of 900 L/min from the reservoir and through the copper tube type K . Compute the pressure at point B, just considering the energy loss due to the straight pipe and neglecting the others losses(elbows and tank outlet)
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it flows horizontally through 100m of piping, and out into the atmosphere. Assume a pump efficiency of 55%, and friction is negligible in the pump suction line. If there are 2 standard elbows and one wide open gate valve in the discharge line, Calculate for a) all friction losses in the system b) the power requirement of the pump if it is to maintain 0.8 m3 / min of flow.
40gal/min of water is pumped and the energy loss in the discharge line is13.5 feet and at the suction line it is 2.5 feet. If the steel suction pipeis 2.5” in diameter and the steel discharge is 1.5” in diameter. The pressureat the distribution tank is 30 psi. Determine a) the pressure at the outlet of thepump b) the power in kW of the pump.
Plz answer in 30min A Francis radial-flow turbine has a runner inlet radius of 2.75 m and its outlet radius is 1.85 m. The runner blade widths are 0.9 m and 2.93 m at the inlet and outlet, respectively. The runner must rotate at 150 rpm to turn the 60-Hz electric generator. The wicket gates turn the flow by angle 35° from radial at the runner inlet, and the flow at the runner outlet is to have angle 20° from radial for proper flow through the draft tube. The volume flow rate at design conditions is 514 m3/s, and the gross head provided by the dam is 100 m. Determine the tangential component of the water velocity at the outlet in m/s.
Calculate the required pump power since the velocity of the water in the pipe is v=1.91 m/s pwater=1000kh/m^3 μ=1.307x10^-3
water from reservoir is pumped over a hill through a pipe 90cm in diameter and a pressure of 200kpa is maintained at the summit where the pipe is 90 m above the reservoir. the quantity pumped is 1.40m/s and by reason of friction there is a head loss of 3 J/N between reservoir and summit. if the pump is 90% efficient, determine the input power of the pump
40gal/min of water is pumped and the energy loss in the discharge line is 13.5 feet and in the suction line it is 2.5 feet. If the steel suction pipe is 2.5” in diameter and the steel discharge pipe is 1.5” in diameter. The pressure in the distribution tank is 30 psi. Determine a) the pressure at the pump outlet b) the power in kW of the pump.
A pipe of diameter 300 mm and length 3 000 m is used for thetransmission of power by water. The total head at the inlet of the pipe is400 m. Find the maximum power available at the outlet of the pipe. Takeƒ = 0.005.
If the flow of 0.10 m3/s of water (mu = 1.31 x 10-3 Pa.s) is to be maintained in the system shown, what power must be added to the water by the pump? The pipe is made of steel and is 15 cm in diameter. Neglect minor losses. TV
water is supplied to the pump at a pressure of 80 kpa and velocity of Va=2m/s. If the discharge is required to be 0.02 m^3/s through the 50 mm diameter pipe, determine the power that the pump must supply to the water to lift it from 8m the total head loss is 0.75m
In below for a pressure head at D of 100 ft, (a) compute the power supplied the turbine DE. (b) If the dashed-line pipewere installed (3000 ft of 24′′), what power would be available to the turbine if the flow were 13.0 mgd? (C = 120)
A reservoir A with elevation 30m connected with a pump to rise the water into two reservoirs B and C 90m and 60 m respectively the amount of flow from J to B is equal 0.11 m/sec use the following data to determine the flow in each pipe and the power of the pump: LAJ 450 m, DaJ = 300 mm, LJB= 300 m, DJB = 200 m, Q JB = 0. m'/sec, LJc 600, D Jc = 150 mm,f (all Pipes) 0.02