Please answer this question, it is about resolving vectors into components 3. A wire is stretched horizontally between two poles that are 8.0m apart. When a50.ON weight is hung 3.0m from the pole on the left side, the wire sags 0.5m.NOTE: Use T, (for the left side) & T2(for the right side)What is the forće exerted by each side of the wire in supporting the weight.

Answered: Image /qna-images/answer/13286f96-75ce-45c6-821a-7e3f1f099c9f.jpg

50.ON weight is hung 3.0m from the pole on the left side, the wire sags 0.5m. What is the force exerted by each side of the wire in supporting the weight. 3. A wire is stretched horizontally between two poles that are 8.0m apart. When a NOTE: Use T1 (for the left side) & T2(for the right side)

50.ON weight is hung 3.0m from the pole on the left side, the wire sags 0.5m. What is the force exerted by each side of the wire in supporting the weight. 3. A wire is stretched horizontally between two poles that are 8.0m apart. When a NOTE: Use T1 (for the left side) & T2(for the right side)

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 12PE: Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the...

See similar textbooks

Related questions

Q: 02 Pin

Q: Three forces F, = 20 N, F2 = 10 N and F, = 5.0 N act on the structure shown in figure below. A…

Q: 12) In the figure, a 10.0-m long bar is attached by a frictionless hinge to a wall and held…

A: Length of the bar is L = 10 m Angle of the rope with the bar is 53 degrees Weight of the bar is W =…

Q: A door has a width of 1 m and a mass of 12 kg. The hinge attaches the door on the left. This time,…

Q: A 12-m uniform beam is hinged to a vertical wall and held horizontally by a 5.0-m cable attached to…

Q: 2. As shown in the picture below, a force of 100 N has to be applied on the left end of the rod in…

A: Given: Force(F)=100N r1 =1.20m r2=0.10m Find Weight (w).…

Q: 5. If the maximum tension that the string can withstand is 4200N, what is the maximum mass that can…

Q: Two people carry an 800 N load with a lightweight pole that is 4.0 m long. The load is placed 1.5 m…

Q: A uniform rod AB is 1.6 m long and weighs 16 N. It is suspended by strings AC and BD as shown. A…

Q: 4. A uniform 312 kg boom is 10.0 m long is held up by cable attached 6.00 m from the wall at an…

Q: A uniform 312 kg boom is 10.0 m long is held up by cable attached 6.00 m from the wall at an angle…

A: Given: The mass of the boom is m=312 kg, The distance of cable from wall is PQ=6 m, The length of…

Q: Find the tension in the cable.

Q: A 60 kg diver stands at the end of a 30 kg springboard, as shown. The board is attached to a hinge…

A: Given data The mass of the springboard is, M1= 30 kg The mass of the diver is, M2= 60 kg Step 1 The…

Q: 10) One end of a uniform beam is hinged to a wall and the other end is supported by a tension wire…

A: The shown beam is in equilibrium. Need to calculate the tension in the wire. Also, it is required to…

Q: 3. The pulley shown in the figure is free to ride on the supporting guide wire. If the pulley…

A: Note:- you have posted two different question. As per guidelines, I will solve first question only.…

Q: Question 3: Determine the force in each member of the truss and state if the members are in tension…

A: The forces are given To find = If the members are in tension or compression .

Q: One end of a uniform beam that weighs 2.95 ✕ 102 N is attached to a wall with a hinge pin. The other…

Q: The diagram shows a sign that wighs 50 N hanging from a uniform horizontal pole. The pole weighs 30…

A: The diagram shows a sign that weighs 50 N hanging from a uniform horizontal pole.

Q: A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold…

A: Given : Weight of scaffold (w1) = 206 N Length (L) = 3.5 m Weight of worker (w2) = 698 N Distance…

Q: 5. A uniform, 120-lb beam is supported in a horizontal position by a pin and cable as shown in the…

A: Given data: Weight of the beam, W=120 lb Angle, θ=370 Length of the beam, L=12 ft

Q: A uniform steel beam has a mass of 890 kg . On it is resting half of an identical beam, as shown in…

A: Draw the free-body diagram of the beam.

Q: please help

A: Given:- Length (L) =3 m mass (m) = 125 kg attached beam lenght (L') =2.8 m angle = 28 degree Find…

Q: 1. Refer to figure 1. A mass is hung by two cables. Calculate the tension in each cable, the…

Q: 9. A beam with a weight of 1650 N is 5.00 m long. It is supported at each end by a post as shown at…

Q: A 70 kg man walks out on a 10 kg beam that rests on, but is not attached to, two supports. When the…

A: At the equilibrium the sum of the forces acts on the beam when it just starts to tip is zero. The…

Q: A 1323-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

Q: 1. A uniform pole 20 ft long and weighing 80 lbs is carried by two men A and B, one at each end of…

A: Given: Length of uniform pole l = 20ft Weight of pole W : 80 lbs

Q: 3) A 560 Ibs uniform pipe is being functioned as a lever as shown in the figure below. A fulcrum…

Q: 20) A 10-m uniform beam weighing 100 N is supported by two vertical ropes at its ends. If a 400-N…

A: Given Length of beam, L = 10 m Weight, W = 100 N 400 N person at 2.0 m from the left end.

Q: 3) A 560 lbs uniform pipe is being functioned as a lever as shown in the figure below. A fulcrum…

Q: 6. Suppose the length L of the uniform bar is 3.0 m and its weight is 210 N. The block's weight is…

A: (a) The horizontal component of force is, Fx=Tmaxcosθ=Wbar+Wblockcosθ=210 N+340 Ncos25°=498.5 N

Q: A 70.0 cmcm, uniform, 40.0 NN shelf is supported horizontally by two vertical wires attached to the…

A: A system is said to be in equilibrium when 1.Net torque = 0 2. Net force = 0

Q: 3. A wire is stretched horizontally between two poles that are 9.0m apart. When a 50.0N weight is…

A: Given: The weight of the object is 50 N. The distance between poles is 9 m. The position of the…

Q: A uniform rod weighing 15 kg is supported in a horizontal position by a pin and wire as shown in…

Q: 2) A wooden beam weighing 2000. N and having a length of 7.200 meters is placed on top of two…

Q: 1.Two people are carrying a uniform wooden ladder that is 3.0 m long and weighs 100 N. if a man…

Q: 4. A uniform rod 2 m long and weighing 65 N is pivoted to the wall as shown. A weight of 25 N is…

Q: The rod is supported by ball-and-socket joint DD and cables ABAB, ACAC. Suppose that FFF = 600 NN…

Q: The large quadriceps muscle in the upper leg terminates at its lower end in a tendon attached to the…

Q: A 70.0 cm, uniform, 40.0 N shelf is supported horizontally by two vertical wires attached to the…

Q: The uniform boom shown below weighs 644 N, and the object hanging from right end weighs 416 N. The…

Q: 1. The beam ABEC carries a bag at the end that weighs 450 kN. As shown on the figure, the beam is…

Q: A 15.7 m long board is supported from beneath at two locations. One is at the far left end of the…

A: center of mass of board is at distance of 7.85 mfrom right weigh mg is acting downwardslet the…

Q: 35.0°% Dinysics Demos SUDDIY Co. The pole is held horizontally by a massless wire under 305 N of…

Q: 1. A 1260 N uniform beam is attached to a vertical wall at one end and is supported by a cable at…

A: Free Body diagram- Torque abut an axis is given by the cross product of the applied force and the…

Q: 3. The uniform seesaw shown below is balanced in a fulcrum located 3.0 m from the left end. The…

Q: A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.069 m, and the…

A: Given,

Q: 1. A uniform 22 kg beam, 3.0 m long, is attached to a wall on the left by a hinge, and is supported…

A: Torque acting on an object is defined as the product of perpendicular force to the distance from the…

Q: A uniform 120-lb beam is supported in a horizontal position by a pin and cable as shown in the…

A: Given, Weight of beam W = 120 lb Length of beam l = 12 ft Angle θ=37∘

Q: A rigid beam (light grey), 1.40 m in length and weighing 8.00 N, is supported at an angle of 30° to…

A: Given data: The mass of the beam is w=8.0 N. The length of beam is L=1.4 m. The angle of beam with…

Concept explainers

Center of Gravity of a system

The centre of gravity is a property that is based on the geometry of a rigid body or any particle. It is described as an equilibrium point or a hypothetical location where the total weight of the body is concentrated.

Question

Please answer this question, it is about resolving vectors into components

3. A wire is stretched horizontally between two poles that are 8.0m apart. When a
50.ON weight is hung 3.0m from the pole on the left side, the wire sags 0.5m.
NOTE: Use T, (for the left side) & T2(for the right side)
What is the forće exerted by each side of the wire in supporting the weight.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) What force must be exerted by the wind to support a 2.50-kg chicken in the position shown in Figure 9.33? (b) What is the ratio of this force to the chicken's weight? (c) Does this support the contention that the chicken has a relatively stable construction? Figure 9.33
Suppose the weight of the drawbridge in Figure 9.34 is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? (b) What is the direction and magnitude of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2500 kg.
One end of a uniform 4.00-m-long rod of weight Fg is supported by a cable at an angle of = 37 with the rod. The other end rests against the wall, where it is held by friction as shown in Figure P12.23. The coefficient of static friction between the wall and the rod is s= 0.500. Determine tile minimum distance x from point A at which an additional object, also with the same weight Fg can be hung without causing the rod to slip at point A.
Explain the need for tall towers on a suspension bridge to ensure stable equilibrium.
3. A uniform 25 N beam 6 m long is carried by two men A and B, one at each end of the beam. a) If A exerts a force of 20 N, where must a load of 45 N be placed on the beam? b) What force does B exert? complete solution please
In a construction site, two vertical cables are supporting a 3.00m steel beam weighing 1500N. Suppose cable A can support a maximum weight of 2000N while cable B can support a maximum weight of 3000N. A construction worker would like to place an object on the horizontal beam, what is the maximum mass that he can put without breaking the cables? where should the object be located?
A sculptor has hung up a 45.0 kg horizontal rod of length 4.85 m . One end of the rod is supported by a pivot, and the other end is held up by a wire. The wire makse a 30.0 ∘ angle with the rod. If tension greater than 1450 N would snap the wire, what is the maximum distance from the pivot that a 68.0 kg person can sit on the rod? r=________m
4. A 3 m long weightless beam is supported at each end by cables. A painter weighing 900 N stands 1 m from the left cable. Calculate the tension in each cable. 5. Where must a 500 N weight be hung on a uniform 150 N pole with a length of 5 m so that a girl at one end supports ¼ as much as a man at the other end? pleasebinclude complete solutions
A window washer is standing on a scaffold supported by a vertical rope at each end. The scaffold weighs 192 N and is 3.3 m long. What is the tension in each rope when the 692–N worker stands 1.18 m from one end?
An 80 kgkg construction worker sits down 2.0 mm from the end of a 1450 kgkg steel beam to eat his lunch, as shown in: 1) Determine the tension in the cable under this scenario. 2) Given that the cable supporting the beam is rated at 1.5×104 N , should the worker be worried? yes/no
A 70.0 cmcm, uniform, 40.0 NN shelf is supported horizontally by two vertical wires attached to the sloping ceiling (Figure 1). A very small 15.0 NN tool is placed on the shelf midway between the points where the wires are attached to it. 1. Find the tension in the left-hand wire. 2. Find the tension in the right-hand wire.
A hungry bear weighing 730 N walks out on a beam in an attempt to retrieve a basket of goodies hanging at the end of the beam (see the figure below). The beam is uniform, weighs 200 N, and is 7.00 m long, and it is supported by a wire at an angle of θ = 60.0°. The basket weighs 80.0 N. (a) If the wire can withstand a maximum tension of 875 N, what is the maximum distance the bear can walk before the wire breaks?