6-16C A constant-velocity horizontal water jet from a stationary nozzle impinges normally on a vertical flat plate that rides on a nearly frictionless track. As the water jet hits the plate, it begins to move due to the water force. Will the acceleration of the plate remain constant or change? Explain. Nozzle Water jet

6-16C A constant-velocity horizontal water jet from a stationary nozzle impinges normally on a vertical flat plate that rides on a nearly frictionless track. As the water jet hits the plate, it begins to move due to the water force. Will the acceleration of the plate remain constant or change? Explain. Nozzle Water jet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
A 50. 95mm diameter horizontal jet of water strikes a plate. Determine the velocity of the jet if 80N of horizontal force is required to move the plate at 2.95m/s at opposite direction as that of jet. Choices 3.31 0.33 1.33 1.13 Note: please base your answer on the given sample choices thank you
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
A constant-velocity horizontal water jet from a stationary nozzle impinges normally on a vertical flat plate that rides on a nearly frictionless track. As the water jet hits the plate, it begins to move due to the water force. Will the acceleration of the plate remain constant or change? Explain.
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be
A 5-cm-diameter horizontal jet of water with a velocity of 30 m/s relative to the ground strikes a flat plate that is moving in the same direction as the jet at a velocity of 20 m/s. The water splatters in all directions in the plane of the plate. How much force does the water stream exert on the plate?
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
Water flowing in a pipe reaches a point where the cross-sectional area of the pipe is reduced to 1/3 of its previous value. If the speed of the water before the constriction is 1.31 m/s, what is the speed of the water after the constriction?
As seen in the figure, a 6 cm diameter water jet (r=1000 kg/m3) hits a plate with a 4 cm diameter hole on it. Some of the jet passes through the hole and some of it deviates. Determine the horizontal force required to hold the plate in place.
An 8-cm-diameter horizontal water jet having a velocity of 35 m/s strikes a vertical stationary flat plate. The water splatters in all directions in the plane of the plate. How much force is required to hold the plate against the water stream?
A 5 cm diameter of water jet strikes a flat plate which held normal to the direction of the water jet and with velocity 3.1617 m/s. Find the work done/s (in Nm/s) (answer in one decimal place) by the jet when the plate is moving with a velocity of 2m/s away from the jet along the same line.
Water enters and leaves the 6-cm-diameter pipe bend inFig. P3.45 at an average velocity of 8.5 m/s. The horizontalforce to support the bend against momentum change is300 N. Find ( a ) the angle ϕ ; and ( b ) the vertical force onthe bend.