6- A mass of 1.2 kg of air at 150 kPa and 12 C is contained in a piston- cylinder device. The air now is compressed to a final pressure of 600 kPa. During this process, heat is transferred from the air such that the temperature inside cylinder remains constant. Calculate: (1) the work done during this process, (2) the amount of heat, and (3) show this process on P-V diagram

6- A mass of 1.2 kg of air at 150 kPa and 12 C is contained in a piston- cylinder device. The air now is compressed to a final pressure of 600 kPa. During this process, heat is transferred from the air such that the temperature inside cylinder remains constant. Calculate: (1) the work done during this process, (2) the amount of heat, and (3) show this process on P-V diagram

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A work producing device of the piston-cylinder system at the beginning contains 1.5 kg of refrigerant-134a at 700 kPa and 120°C. At this stage, the piston stops at the top dead center (TDC). To move the mass of the piston 400 kPa pressure is required. A valve at the bottom (BDC) of the cylinder is opened, and the gas is withdrawn from it. After a few seconds, the piston starts to move and the valve is closed when half of the gas is withdrawn from the cylinder and the temperature in the cylinder drops to 30°C. (a) Sketch the PVDiagram of this process and determine (b) the work done, (c) the heat transfer to the surrounding
Twokg of saturated water vapor at 600 kPa are contained in a piston–cylinder device. The water expands adiabatically until the pressure is 100 kPa and is said to produce 700 kJ of work output. Is this process realistic? Using the T-s diagram for the process and the concepts of the second law, support your answer.
Air is compressed in a compressor through the purely polytropic, purely isothermal, and intercooling as shown in the diagram between the same pressure limits. Select the area that indicates the work saved for the intercooling process comparing to the purely polytropic one _____________ A. 1-X'-2'-P2-P1-1 B. X-X'-2-2"-X C. 1-X-X'-2-P2-P1-1 D. 1-X'-2"-P2-P1-1
A piston-cylinder assembly initially contains 100 kPa pressure and 2 liters of air at 25°C. Then the air is compressed to a pressure of 620 kPa and a temperature of 160 ° C. The useful work done for compression is 1.22 k). Considering that the ambient pressure and temperature are 100 kPa and 25°C respectively, a) Calculate the usability of air in the initial and final states., b) Calculate the minimum work required for the compression process. c) Calculate the second-law efficiency of the state change. (Please solve in detail and according to engineering rules. ) Thermodynamics
Steam is contained in a 2-L volume at a pressure of 2.0 MPa and a temperature of 400°C. If the pressure is held constant by expanding the volume while 20 kJ of heat is added, what is the final temperature and the work done?
A piston system contains a hot fluid at 250kPa pressure that is cooled while being stirred by a paddle wheel. Initially, the internal energy of the fluid is 1500 kJ and volume is 2m3. During the cooling process, the fluid loses 400 kJ of heat, and the paddle wheel does 100 kJ of work on the fluid. At the end, volume reduces to 0.5m3. Pressure remains constant. Determine the final internal energy of the fluid. Neglect the energy stored in the paddle wheel.
A piston-cylinder assembly contains R-134a refrigerant in a volume of 0.15 m3, 0.28 MPa and 40 ° C. Initially the piston is fixed with a pin. The piston-cylinder assembly is heated from a heat source at 150 ° C and the pressure rises to 0.32 MPa. Then the pin is pulled and heat is transferred to an environment at 25 ° C, allowing the R-134a refrigerant to reach 50 ° C at constant pressure. a) Calculate the amount of heat and work transfer in processes. b) Calculate the entropy generation in processes. Comment on the conformity of the processes to the second law of thermodynamics.
An adiabatic piston-cylinder device equipped with aspring maintains the pressure inside at 300 kPa, when thevolume is 0, and in 3 000 kPa, when the volume is 5 m ^ 3. Thedevice connects to a steam supply lineat 1,500 kPa and 200 ° C, and at the beginning the volume of the cylinder is 0.Determine the final temperature (and quality, if applicable) whenthe valve is opened and water vapor is allowed to enter from thesupply to the cylinder, until the pressure inside is equal tothe one on the line. Also determine the total workperformed during this adiabatic filling process.
Refrigerant-134a (R-134a) enters the expansion valve of a refrigeration system at 650 kPa with a quality of 20%. The pressure of R-134a at the outlet is 200 kPa. a)Determine the temperature of R-134a at the outlet in oC. Calculate the difference of internal energy between the outlet and inlet in kJ/kg
Choose correct answer: Consider an insulated system with piston and cylinder arrangement in which helium gas is present. If 100000 J of work is given to the helium gas, then the change in internal energy is _________ A. 100 kJ B. -100 kJ C. 10000 J D. -100000 J
An ideal free piston-cylinder with an initial volume of 0.5500 m3contains 19.00 kg of refrigerant R-134a at an initial pressure of 400.0kPa. The device is filled with R134a from a source at 40.00°C and1.000 MPa until there is 800.0 kg of saturated liquid refrigerant R134ain the piston-cylinder device. The tank is well insulated, and no heattransfer to the ambient air at 30.00°C occurs during the process. Duringthe charging process, a refrigerator with COPR = 1.900 extracts heatfrom the refrigerant R-134a in the piston-cylinder device such that thecharging process occurs in an isothermal manner (constanttemperature).i) Determine the initial state and temperature of the R-134a (in °C).ii) Determine the boundary work done during the process (in kJ).iii) Determine the amount of energy (in kJ) and the cost (in $) therefrigerator consumes to maintain the process to be isothermal.Assume electrical energy costs $0.35 /kW.hr.iv) It is claimed that a refrigerator could supply the required…
If a certain gas has Cp of 1.005 kJ/kg-K and Cv of 0.678 kJ/kg-K, determine the value of k, T2, T3,T4, and thermal efficiency of the gas considering the given information below A gas is primarily at a pressure of 101.325 kPa and a temperature of 77˚C go through the subsequent cycle: For process 1-2 it undergoes an adiabatic compression through compression ratio 5:1; for the process 2-3, it undertakes a heating at constant volume through a pressure ratio 2:1; for process 3-4, it commences constant pressure expansion to initial pressure; and for the last process, which is the process 4-1, it takes a constant pressure cooling to initial volume.