(6) Choose a) Which one of the following transistors cannot operate with VGS=0. 1. JFET. 2. D-MOSFET. 3. E-MOSFET. b) If the VGs in an n-channel D-MOSFET is made more negative, the drain current will. 1. Increase. 2. Decrease. 3. Be zero. c) A MOSFET differs from JFET mainly because: 1. MOSFETs do not have a physical channel. 2. The JFET has a pn junction. 3. of the power rating. d) The n-channel D-MOSFET with a positive Vas is operating in: 1. The depletion mode. 2. The enhancement mode. 3. Saturation.

(6) Choose a) Which one of the following transistors cannot operate with VGS=0. 1. JFET. 2. D-MOSFET. 3. E-MOSFET. b) If the VGs in an n-channel D-MOSFET is made more negative, the drain current will. 1. Increase. 2. Decrease. 3. Be zero. c) A MOSFET differs from JFET mainly because: 1. MOSFETs do not have a physical channel. 2. The JFET has a pn junction. 3. of the power rating. d) The n-channel D-MOSFET with a positive Vas is operating in: 1. The depletion mode. 2. The enhancement mode. 3. Saturation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

See attached picture: Which two transistors are p-type and which two are n-type? Refer to the transistors by their labels (a, b, c, or d). Also, which transistors (a, b, c, or d) are “ON” when: A) Input A = 0, Input B = 0 B) Input A = 1, Input B = 0 C) Input A = 0, Input B = 1 D) Input A = 1, Input B = 1
The output characteristics of a bipolar transistor appear as shown. (a) What are the values of βF and βo at IB = 4 μA and VCE = 10 V?(b) What are the values of βF and βo at IB = 8 μA and VCE = 10 V?
Question 1: Draw and explain the transistor amplifier, which is usually referred as emitter follower.Also, (i) derive its voltage and current gains by equivalent circuit; (ii) compare its voltage and current gains with other transistor amplifiers. Question 2:(a) Predict the name of the curve drawn between ID and VGS of the JFET and represent the cut off voltage in it. (b) E-MOSFET has ID(on) = 600mA (minimum) at VGS = 9V and VGS(th) = 1 V. Find the drain current for VGS = 6 V. Question 3: (a) State the name of the power amplifier, which has a efficiency as 10% in practical case and also derive and prove its theoretical efficiency is 25%. (b) Explain the role of Q point in power amplifiers based on its location in AC load line.…
For identical transistors, find the voltage values of Idss = 8mA, Vp0 = 4v and iG = 0.1 μ A. If Vdd = 15 V, Rd = 1 kohm and Rg = 1Mohm, find the voltage values VdsQ1, VdsQ2.
Figure 1 shows the transfer curve of a network with an unknown channel Junction Field Effect Transistor (JFET). (i) Identify the channel of the JFET; justify your answer. (ii) Given the supply voltage of 16 ?, design a voltage divider network using the JFET in (i) above. Take ?1 = 1400??; ?2 = 180??; and ?? = 10 ?. Please use the nearest standard resistor values. (iii) With the obtained standard resistance values in (ii) above, determine the new ??? and ????, using the mathematical approach only.
Since Vcc = 12 V, Vin = 690 mV, RB = 780 kΩ, RC1 = 27.9 Ω, RC2 = 25.4 Ω, RE = 470 Ω, RL = 47 Ω and β1 = β2 = 100 in the circuit in the figure Find the current (IL) flowing through RL? NOTE-1: VBE1 = VBE2 = 0.7 V will be taken. NOTE-2: Output impedances of transistors (r0) will be neglected.
The dc bias circuit for a common emitter amplifier is shown in the figure. In the circuit, Vcc=15v,RB1=20k Ω,RB2=100k Ω,Rc=5.1k Ω,and RE1=1k Ω, Assume that when the transistor is on, the voltage drop from base to emitter VBE=0.7v. Also assume that β= ∞, which implies that the base current can be considered zero (IB=0) in your calculations. Solve for the base voltage VB. Solve for the emitter voltage VE. Solve for the emitter current IB. Solve for the collector current IC
2. A student picks up a MOSFET in his lab and has no idea of what kind of transistor is it, he only knows the name of the three terminals:Gate, Source and DrainThe Pinch off voltage he found was Vp=4V and Idss=10mAa. What channel type of a transistor is it? Sketch it’s junction diagram.b. Find drain current for Vgs= −1,0,1,2,4c. Sketch the transfer curve for this transistor showing the two operational regions.d. Use the transfer curve to draw a characteristic curve, showing the ohmic region, pinch off voltage, saturation region and breakdown voltage.
(a)(i) State three differences between the Field Effect Transistor (FET) and the Bipolar JunctionTransistor (BJT). (ii) Draw the physical structure and device symbol for an n-channel JFET. (iii) What is meant by drain characteristics (b) Determine the drain current of an n-channel JFET having pinch-off voltage VP = - 4 and drain-source saturation current IDSS=12mA at the following gate-source voltages(i) VGS= 0V(ii) VGS= -2V (c) Calculate the transconductance, gm of a JFET having specified values of IDSS=12mA and VP= - 4V at bias points(i) VGS= 0V and(ii) VGS= -1.5V.
Considering the given transistor circuit and given values(β=60; V BE =0,5 V; VCC =15V; R E=1K ; R c=10K ; R1=60K ;R2=30K ).a. Find the base, collector, and emitter currents b. Find the voltage gain of this circuit c. Find the voltage gain by ignoring the capacitor connected to the emitterd. Briefly describe the transistor active zone and state its importance
Q3:Choose One of the following: : (A)In common emmiter voltage divider bias of BJT, Vcc = 25V; R1= 10 k ohm; R2, = 2.2 k ohm ;Rc = 3.6 k ohm and RE = 1 k ohm.Determain Vec at ß = 120.using Exact analysis Draw the equvelent circuit inaddition the DC load line curve . (B)For self bais(Emitter resistace bais) of BJT,Vcc= 22 V, lb = 45macroA, a = 0.99, RE = 1 k ohm. Determain VCe Draw the equvelent circuit inaddition to DC load line curve.
Since the transistors used in the circuit are b=200 and r0= ∞(endless);A) By analyzing the DC for each amplifier floor separatelyre1, re2 find resistance values.B) Draw the AC equivalent circuit of the amplifier circuit.C) For each floor Zi=?, Z0 =?D) For each amplifier floor Av1, Av2 find the tension gains.E) Avl find Vl voltage value by finding voltage gain.