A pipe of diameter 400 mm carries water at a velocity of 20 m/s.The pressure ta point A is 300000 N/m2 and at point B is 200000 N/m2, while the datum head at A and Bare 20 m and 25 m respectively. Find the loss of head (HL) between A and . B A-4.5 m O B-5.19 m O C- 6.2 m O D-5.6 m O E- 7.1 m O

A pipe of diameter 400 mm carries water at a velocity of 20 m/s.The pressure ta point A is 300000 N/m2 and at point B is 200000 N/m2, while the datum head at A and Bare 20 m and 25 m respectively. Find the loss of head (HL) between A and . B A-4.5 m O B-5.19 m O C- 6.2 m O D-5.6 m O E- 7.1 m O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ity of 25 m/s. 1 he pressures; Iy while the datum head at WJ A pipe of diameter 400 mm carries water L oints A and B are given as 29.43 Nfem” and 22.563 Nfcm respective B are 28 m and 30 m. Find the loss of head betweert A and B
A pipe reduces it size from 300mm diameter at point 1, to 100mm diameter at point 2. The pressure at point 1 is 200KPa, and point 2 is 7m higher in elevation than point 1. The discharge on the pipe is 30 L/s and the head loss from point 1 to 2 is 10% of the pressure head at point 1. Determine the pressure at point 2 if a) the liquid is water, b) if the liquid is oil (SG = 0.8) and c) if the liquid is glycerin (SG = 1.3)
A pump is required to move water at a design discharge of 1m3 /s between reservoirA to reservoir B (see schematic below). The difference in surface water elevations between A and B is10m. The difference in elevation between the surface elevation of A and the center of the first pipe sectionis 2m. The pipe is to be commercial steel with an internal diameter of 35cm. Determine the maximumdistance, LAP, from reservoir A that the pump could be installed without encountering cavitationproblems. Consider minor losses of a sharp-edged inlet. Assume a kinematic viscosity of 1x10-6 m 2/s and a specific weight of 9.79kN/m3 . Assume STP conditions (i.e., Pvapor = 3kPa, Patm=101.3kPa)
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
Two pipes are connected in series with a diameter ratio of 2:5. If the flow velocity in the smaller diameter pipe is 12 m/s, determine the head loss due to: a. sudden contraction, b. sudden enlargement.
A sharp-edged orifice in the vertical wall of a large tank has a diameter of 25 mm. The coefficient of contraction is 0.620 and the coefficient of velocity is 0.98. If the jet drops 936 mm in a horizontal distance of 2.490 meter from the vena contract, Determine the power loss in watts.
A pump is required to pump water from a large reservoir to the water tower located 20 m above thereservoir (Figure 1). If 0.03 m3/s of water having a density of 1000 kg/m3is pumped through a 30-mmpipe.a. How much power is required to be delivered to the water by the pump? Consider the flow lossesin the pipe; do the necessary assumptions. b. Determine the efficiency of the pump
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 1.64 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.94 m.
A pump is fitted to 100 m pipeline that connects reservoir A reservoir B. The diameter of the pipe is 200 mm and is characterized by a fri factor of 0.02. The design discharge is 0.15 m³/s and the pump. Assuming th minor losses are 20% of friction losses, determine the head the pump must p
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h. The inlet is fed by a pump at an absolute pressure of 4 MPa.The exit is at standard atmospheric pressure (101 kPa) and is 200 m higher. Calculate the frictional head loss Hf and compare it to the velocity head of the flow.
A pipe experienced a total head loss of 15 m, determine thepressure difference from its starting point to discharge point inkPa.