I need answer within 20 minutes please please with my best wishes is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then6)pushing the metal into the opening using a punch & Blank holder to make box-shaped parts.7) Products possess (shows) better reproducibility in metal forming at8)forming temperature condition.In blanking opcration, if thc final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be9)property in the work piece.&Cold working of metals decreases10) Sheet metal bending inIvolves11) Most sheet metal working operations are performed as12) One of the factors that increase's spring back is13) Friction and tool wear is more pronounced (occurs clearly) in14) In roll piercing, the production of seamless tubes is done by15) In flat rollıng, spreading tends to be pronounced (occur clearly) with a work piece ofstresses and strains.forming condition.forming condition.width to thickness ratio.forming processs

Only four multiple questions are allowed to solve.

6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then pushing the metal into the opening using a punch & Blank holder to make box-shaped parts. Products possess (shows) better reproducibility in metal forming at 7) forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be 9) Cold working of metals decreases m. property in the work piece. 10) Sheet metal bending involves stresses and strains. forming condition

6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and then pushing the metal into the opening using a punch & Blank holder to make box-shaped parts. Products possess (shows) better reproducibility in metal forming at 7) forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die size should be 9) Cold working of metals decreases m. property in the work piece. 10) Sheet metal bending involves stresses and strains. forming condition

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q#4:(a) Explainthe advantage of corner radii of punch and die in Sheet Metal Drawing Process.
A drawing operation is used to form a cylindrical cup with inside diameter of 75 mm and height of 50 mm. The starting blank size is 140 mm and the stock thickness is 2.4 mm. Based on the data, is the operation feasible?
Forging procedures may be classified in part by how much room there is for movement in the die. Please identify the three primary classes that this system generates.
The average number of articles produced by two machines per day are 200 and 250 with S.D 20 and 25 respectively on the basis of records of 25 days production.Can you regard both the machines equally efficient at 1% level of significant?
1. Derive an expression for the reduction r in drawing as a function of drawing ratio DR.2. A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its insidediameter = 100 mm. The sheet-metal thickness = 2 mm. If the blank diameter = 225 mm, determine(a) drawing ratio, (b) reduction, and (c) thickness-to-diameter ratio. (d) Does the operation seem feasible?3. A drawing operation is used to form a cylindrical cup with inside diameter = 65 mm and height =50mm. The starting blank size = 140 mm and the stock thickness = 2.8mm. determine (a) drawing forceand (b) holding force, given that the tensile strength of the sheet metal (low-carbon steel) = 350 MPa andyield strength = 190 MPa. The die corner radius = 6 mm. Based on these data, is the operation feasible?
IDENTIFICATION: ___________1. It is also known as roll forming. ___________2. It is the most common cold extrusion process. ___________3. This process is the most rapid method of converting large sections into desired shapes. ___________4. This method is uses for production of hollow castings without the use of cores. ___________5. A die is usually made in two halves, What is the movable half called?
Q#1: (a) Explain the advantage of corner radii of punch and die in Sheet Metal Drawing Process. (b) Explain the disadvantages of Tube Drawing process in which mandrel is not used.
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
(USCS units) A part is hot forged in an impression die. The projected area of the part, including flash, = 17.3 in2. After trimming, the part has a projected area of 12.5 in2. Part geometry is complex. As heated the work metal yields at 13,000 lb/in2and no strain hardening occurs. At room temperature, the metal yields at 30,000 lb/in2. Determine the maximum force required to perform the forging operation. (use table 18.1 for Kf )
Identify the type of forming process in which the material is required to pass repeatedly through dies of different size. a. Drop forging process b. Wire drawing process c. Rolling process d. Extrusion proces
In rolling process 40mm thick plate is rolled to 20mm in two high rolling mills. Roll diameter is 200mm the angle of contact is 15degree. Determine no of roll passes required to obtain final desires thickness
17 In the open die forging ,a high precision is obtained. Select one: True False