6. Discussion: 1. Is there a difference between the values of the nozzle velocity (v₁) and the jet velocity (vj)? Why? 2. Is there a difference between the values of the water jet force on plate (F₁) when change the plate shape (flat, Conical, and Hemispherical plate)? Why? 3. Is there a difference between the values of the water jet force on plate (F₁) and the force exerted by weights on fluid (Fexp)? Why? 4. What is the relationship type in the plot between (Fexp) versus (p Qvj)? Why? 5. Is there a difference between the slope from plot and the slope of the value (1-Cos)? Why?

6. Discussion: 1. Is there a difference between the values of the nozzle velocity (v₁) and the jet velocity (vj)? Why? 2. Is there a difference between the values of the water jet force on plate (F₁) when change the plate shape (flat, Conical, and Hemispherical plate)? Why? 3. Is there a difference between the values of the water jet force on plate (F₁) and the force exerted by weights on fluid (Fexp)? Why? 4. What is the relationship type in the plot between (Fexp) versus (p Qvj)? Why? 5. Is there a difference between the slope from plot and the slope of the value (1-Cos)? Why?

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

I'm looking for a conclusion based on this given result from the hydrostatic pressure on plane surface 1. PARTIAL IMMERSION Trials 1 2 3 Total weight on arm M (grams) 50 g 100 g 150 g Depth of Water y (mm) 49 mm 65 mm 80 mm Force on End Surface (experimental) (N) 734.41 N 1512.76 N 2334.59 N Force on End Surface (theoretical) (N) 883,267,875 N 1,554,271,875 N 2,354,400,000 N Depth of Center of Pressure (mm) 16.33 mm 12.67 mm 26.67 mm 2. COMPLETE IMMERSION Trials 1 2 3 Total weight on arm M (grams) 250 g 300 g 450 g Depth of Water y (mm) 109 mm 122 mm 160 mm Force on End Surface (experimental) (N) 4109.31 N 5009.00 N 7704.15 N Force on End Surface (theoretical) (N) 4,340,925,000 N 5,297,400,000 N 8,093,250,000 N Depth of Center of Pressure (mm) 73.12 mm 83.57 mm 117.58 mm
A rectangular tank 3 m x 4 m is 5 m high with 2 orifices placed at a vertical distances of 0.5 m and 1m from the bottom respectively. Both orifices are 100 mm diameter with C=0.607. Determine the: show complete solution a. How long will it take to lower the water at tank by 2 m in seconds?b. How long will it take for the water surface to be at the same level as the upper orifice in seconds?
A storage tank has vertical sides and is filled with water to a depth of 1.5 m. On top of the water is found an additional layer of oil (SG = 0.8) with a thickness of 0.5 m. Assuming a unit thickness into the page, calculate the following: (a) Resultant force on the wall of the tank due to the fluids? (b) Moment caused by the fluids along the wall at the base of the tank?
A cylindrical tank having a diameter of 1.5 m and a height of 4 m is open at one end and close at the other end. It is placed below the water surface with its open end down. How deep below the water surface should the tank be placed if the depth of the water inside the tank is 1.8 m? a.6.0 cm b.5.90cm c.6.25cm d.7.0cm show your complete solution
Water is flowing into a frustum of a conical vessel 2 m high at 100 liters per minute. The vessel had a radii of 1.0 m and 1.5 m at the bottom and top respectively. Find the height of water when the water surface is rising at 25.72 mm/min. a. 44 cm b. 45 cm c. 46 cm d. 47 cm
Hydraulics 6. Determine the Reynolds number of a 0.40 cubic meter per second oil of Gs=0.80 and an absolute viscosity of 0.025 Pa.s thru a 450 mm diameter pipe.
What height of a column of a special gage liquid (sp. gr. = 2.95) exert the same pressure as a column of oil 4.5 meters high (sp.gr. = 1.19)? a. 1.58 m b. 1.28 m c. 1.85 m d. 1.82 m
A wooden block (40 cm wide (b), 20 cm long (h) and 15 cm deep) floats on the seawater (specific gravity, sg = 1.025) with a depth of immersion is 12 cm. Calculate the position of metacentre, MG and justify the stability of block with the aid of sketch.
Water flows from a large reservoir A to a lower large reservoir B through 291 m of smooth sloped piping as shown in the drawing. Both reservoirs have their surfaces open to the open air, the specific mass of the water is 998 kg/m³ and the kinematic viscosity of the water is equal to 0.00000101 m²/s. The internal diameter of the pipe is 0.091 m and the average velocity of water flowing through this pipe is 2 m/s. Neglecting the localized head losses of the tube inlet and outlet in the reservoirs, calculate the difference in the dimensions of the reservoir surfaces in m necessary to maintain the average flow velocity in the tube at this given value of 2 m/s. Suggestion: Use the explicit S.E. Haaland equation for the calculation of the friction factor.
Length of Pipe 1 = 300 m Length of Pipe 2 = 240 m Length of Pipe 3 = 210 m Length of Pipe 4 = 450 m *Pipe 2 and Pipe 3 are parallel Diameter of Pipe 1 = 200 mm Diameter of Pipe 2 = 150 mm Diameter of Pipe 4 = 250 mm discharge of the pipe system = 45 Liters/second Total hf = 8 meters f= 0.02 What is the diameter of Pipe 3? (in mm)
Use the design values for the coefficient C, from Table 8.3 unless stated otherwise. Use either of the various forms of the formula or the nomograph in Fig. 8.10 as assigned. 8.63 Water flows at a rate of 1.50 ft/s through 550 ft of 6-in cement-lined ductile iron pipe. Compute the energy loss.
A pressure gage 7.0 m above the bottom of a tank containing a liquid reads 64.94 kPa; another gage at height 4.0 m reads 87.53 kPa. Compute the specific weight and mass density of the fluid.