6. For the gate shown, a = 45°C, yı = 1 m, and y2 = 3 m. Will the gate fall or stay in position under the action of the hydrostatic and gravity forces if the gate itself weighs 90 kN and is 1.0 m wide (rectangular gate)? Taking y = 9810 N/m³ use calculations to justify your answer. Water Standard atmospheric pressure Gate Hinge.

6. For the gate shown, a = 45°C, yı = 1 m, and y2 = 3 m. Will the gate fall or stay in position under the action of the hydrostatic and gravity forces if the gate itself weighs 90 kN and is 1.0 m wide (rectangular gate)? Taking y = 9810 N/m³ use calculations to justify your answer. Water Standard atmospheric pressure Gate Hinge.

Name: 6. For the gate shown, a = 45°C, yı = 1 m, and y2 = 3 m. Will the gat
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 6. For the gate shown, a = 45°C, yı = 1 m, and y2 = 3 m. Will the gate fall or stay inposition under the action of the hydrostatic and gravity forces if the gate itself weighs90 kN and is 1.0 m wide (rectangular gate)? Taking y = 9810 N/m³ use calcu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Include also the free body diagram or figure of the problem, and your findings after solving it.
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if (G. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation for the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the cover (D = 4 m). Find the magnitude of the applied force (Fa) as shown.
2. Estimate the vacuum pressure that should be created by a suction pump in order to lift a ground water which is 10m below the level ground. Neglect the effect of pipe friction. Draw the figure or free body diagram, and explain its step by step solution. 3. Supposed that air (std.) has a uniform density of 1.2kg/m^3, estimate how high (meters) above the sea level where there exists a zero pressure. Assume that in the given condition, barometric pressure at sea level is 101.325 kPa. Draw the figure or free body diagram, and explain its step by step solution.
A semicircular 40-ft-diameter tunnel is to be built under a 150-ft-deep, 800-ft-long lake. Determine the total hydrostatic force acting on the roof of the tunnel.
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
A triangular wooden body (S=0.80) is placed in water in theposition indicated in the figure. If the width of the body is 7.0 m,determine if the same for this position is stable or not indicating themetacentric height (YM).
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?
An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasoline would begin to spill? notw: include free body diagram