An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasol

An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasol

Name: An open rectangular tank 1 m wide and 2 m long contains gasoline to a
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: An open rectangular tank 1 m wide and 2 m long contains gasoline to a depth of 1 m. If the height of the tank sides is 1.5 m, what is the maximum horizontal acceleration (along the long axis of the tank) that can develop before the gasoline would beg

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

An open cylindrical vessel 60cm in diameter and 1.20m high contains water to a depth of 1m. If it is rotated about its vertical axis, determine the angular velocity w if: a)The water surface just touches the edge of the open top without spillage.
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Using appropriate software, investigate the effect of water depth on the force exerted on the plate by the ridge. Let the water depth vary from 0 to 5 m in increments of 0.5 m. Tabulate and plot your results.
An oil tanker 3m wide 2 m deep and 10 m long contains oil of density 800 kg/m3, if the tanker is closed and completely filled with the oil and accelerated horizontally at 3m/s2. a.) determine the total liquid thrust (hydrostatic force) on the front end. (in kN) b.) determine the total liquid thrust (hydrostatic force) on the rear end. (in kN)
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A rectangular car is 3 m. long by 1.5 m wide and 1.5 m deep. If friction is neglected and the car rolls down a plane with an inclination of 20 degrees, what is the inclination of the water surface if the car contained 0.60 m depth of water when the car was horizontal?
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Fig. below. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge.
A 15-ft-long, 6-ft-high rectangular tank open to the atmosphere is towed by a truck on a level road. The tank is filled with water to a depth of 5 ft. Determine the maximum acceleration or deceleration allowed if no water is to spill during towing.
What force, F, must be applied to the S-shaped gate to keep it closed? The gate is 1 m wide andthe radius of curvature of each part is 1 m. The liquid is water.
Piston A has a cross-section of 1,200 cm^2 while that of piston B is 950 cm^2 with the latter higher than piston A by 1.75 m. If the intervening passages are filled with oil (s= 0.8), what is the difference in pressure between A and B?
5) Before transferring the rod into the graduated cylinder, the cylinder tipped and some of the water splashed from the cylinder. The student did not redo the volume. Will the student’s calculated density be higher, lower or the same as the actual density of the rod? Explain.
A vertical cylindrical container contains 5840 gallons of gasoline and is 1.53 m in radius. Due to evaporation within the tank, the pressure on the top of the fluid is 2.5 times normal atmospheric pressure. The density of gasoline is 737 kg/m3. a. What is the pressure at the bottom of the tank? b. If a nozzle at the bottom of the tank is used to let fuel out, with what velocity would the gasoline exit the hole? c. If a nozzle at the bottom of the tank is used to let fuel out, what volume flow rate will result if the diameter of the hole is 1.2 cm? d. At what initial rate will the height of the fuel level in the tank drop as fuel is removed?