6. Identify the process/es in which the entropy change is positive among the following. i, Increase in the volume of a gas at constant temperature. ii. water (g) -water (I). iii. Increase in pressure of a gas. iv. Increase in temperature of a substance. a. ii only b. i, ii, and iii cionly d. į and iv

6. Identify the process/es in which the entropy change is positive among the following. i, Increase in the volume of a gas at constant temperature. ii. water (g) -water (I). iii. Increase in pressure of a gas. iv. Increase in temperature of a substance. a. ii only b. i, ii, and iii cionly d. į and iv

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

22-A closed vessel was initially filled with water at a dryness of 11% at a pressure of 350 kPa. Then, coarse heat transfer is made until the dryness degree is 45% at constant pressure. What is the entropy change? A) 1,790 kJ/kgK B) 2,304 kJ/kgK C) 1,512 kJ/kgK D) 1,772 kJ/kgK E) 1,756 kJ/kgK
Establish the increase of entropy principle.
8Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.2, 420°R, with a velocity of 1800 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2000°R before being discharged through the nozzle at 6 lbf/in.2 On the basis of an air-standard analysis, determine:(a) the pressure at the diffuser exit, in lbf/in.2(b) the velocity at the nozzle exit, in ft/s.Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic.
Air with a mass flow rate of 3 kg/s enters a horizontal nozzle operating at steady state at 400 K, 300 kPa, and velocity of 2.5 m/s. At the exit, the temperature is 250 K and the velocity is 400 m/s. Using the ideal gas model for air with constant cp = 1.011 kJ/kg · K, determine a. the area at the inlet, in m2. b. the heat transfer between the nozzle at its surroundings, in kW. Specify whether the heat transfer is to or from the air.
Determine a) change in entropy b) heat c) work non flow d) work steady flow
15 - A fixed volume insulated tank, initially empty, was connected to a distribution line carrying helium gas at a temperature of 135ºC by means of a valve. The valve is opened first and closed when the pressure is the same as the distribution line pressure. What is the final internal energy of helium in the tank? (Internal energy of the warehouse in the final state = Enthalpy of the distribution line). (Cp=5.1926) will be taken. a) 701.0 kJ/kg B) 597.1 kJ/kg NS) 2014.7 kJ/kg D) 2066.7 kJ/kg TO) 2118.6 kJ/kg
Steam enters a nozzle operating at steady state at 20 bar, 263°C, with a velocity of 52 m/s. The exit pressure and temperature are 8 bar and 162°C, respectively. The mass flow rate is 2.9 kg/s. Neglecting heat transfer and potential energy, determine the inlet area in cm2.
Figure shows data for a portion of the ducting in ventilation system operating at steady state. The ducts are well insulated and the pressure is very nearly 1 bar throughout. Assuming the ideal gas model for air with Cp = 1 kJ/kg · K. and ignoring kinetic and potential energy effects, determine: (a) the temperature of the air at the exit, in °C. (b) the exit diameter, in m. (c) the rate of entropy production within the duct, in kJ/min.
Nitrogen, modeled as an ideal gas, flows at a rate of 3 kg/s through a well-insulated horizontal nozzle operating at steady state. The nitrogen enters the nozzle with a velocity of 20 m/s at 400 K, 400 kPa and exits the nozzle at 100 kPa.To achieve an exit velocity of 500 m/s, determine:(a) the exit temperature, in K.(b) the exit area, in m2.
Steam enters a one-inlet, two-exit control volume at location (1) at 360°C, 100 bar, with a mass flow rate of 2 kg/s. The inlet pipe is round with a diameter of 5.2 cm. Fifteen percent of the flow leaves through location (2) and the remainder leaves at (3). For steady-state operation, determine the inlet velocity, in m/s, and the mass flow rate at each exit, in kg/s.
A 1.2 L car engine has four individual cylinders, each one of which holds 0.3 L of fuel + air gas mixture. When the fuel + air gas mixture enters the piston at 1 atm pressure at a standard engine temperature of ~90 °C (again 0.3 L volume), it is compressed adiabatically and irreversibly by a constant external pressure of 608 kPa. Assuming Cv,m = 20.8 J/K/mol, what is Δq, n, P (final), T (final), ΔU, ΔW and ΔH? Assume perfect gas behavior
One kilogram of water contained in a piston-cylinder assembly, initially at 160°C, 150 kPa, undergoes an isothermal compression process to saturated liquid. For the process, W = -471.5 kJ. Determine for the process, (a) the heat transfer, in kJ. (b) the change in entropy, in kJ/K. Show the process on a sketch of the T-s diagram.