MECHANICAL VIBRATION 6.13 6.13. Assuming small oscillations, derive the differential equations of motion of thetwo degree of freedom system shown in Fig. P6.10. Determine the responseof the system, as a function of time, to the harmonic forcing function T(t). T(t) = T, sin mtm2Fig. P6.10

Answered: Image /qna-images/answer/5a0341cb-d647-4c26-afeb-741cfb7dcd0a.jpg

Answered: 6.13. Assuming small oscillations,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple pendulum of length L is set to oscillate in simple harmonic motion. The bob gravitational potential energy is zero at its lowest vertical point. When the bob's height is at half its maximum, h = hmax/2, then its velocity is:
A wooden rectangular block of density p, height h and cross section b x a is depressed in an oil tub of density po and made to vibrate freely in the vertical direction. Neglecting the damping effect , find the natural frequency
spring-mass system with m = 0.01 Mg and k = 5 kN/m is subjected to a harmonic force of amplitude 0.25 kN and frequency ωo. If the maximum amplitude of the forced motion of the mass (particular solution or steady state) is observed to be 100 mm, find the value of ωo
A rigid and weightless rod is restricted to oscillations in the vertical plane as shown in the figure below.Determine the natural frequency of the system of mass m.
Suppose that an object attached to a coiled spring is pulled down a distance of 10 inches from its rest position and then released. If the time for one oscillation is 3 seconds, find the displacement d of the object from its rest position after time t = 10 seconds. Assume no friction
(a) A mass suspended from a helical spring of stiffness s, is displaced by a distance x from its equilibrium position and allowed to vibrate. Show that the motion is simple harmonic. (b) A vertical helical spring having a stiffness of 1540 N/m is clamped at its upper end and carries a mass of 20 kg attached to the lower end. The mass is displaced vertically through a distance of 120 mm and released. Find : 1. Frequency of oscillation ; 2. Maximum velocity reached ; 3. Maximum acceleration; and 4. Maximum value of the inertia force on the mass. (c) A machine of mass 75 kg is mounted on springs and is fitted with a dashpot to damp out vibrations. There are three springs each of stiffness 10 N/mm and it is found that the amplitude of vibration diminishes from 38.4 mm to 6.4 mm in two complete oscillations. Assuming that the damping force varies as the velocity, determine : 1. the resistance of the dashpot at unit velocity ; 2. the ratio of the frequency of the damped vibration to the…
An elastic string of natural length 4a is fixed at one end to a point O.its hangs vertically and carries at its other end a particle of mass 2m , In the position of equilibrium ,the length of the string is 5a Find, i)The modulus of elasticity of the string ii)The period of small vertical oscillations of the particle when it is pulled downward from its equilibrium position and then released
How is constant amplitude sustained in forced oscillations?
The mass of a spring-mass system, with m = 12 kg and k = 35 kN/m, vibrates on a horizontal surface under a harmonic force of magnitude 300 and a frequency of 19 Hz. Find the resulting amplitude of steady state vibration. Assumethe coefficient of friction between the mass and the horizontal surface as 0.25
Two masses m1 and m2 each connected by two springs of stiffness k, are connected by a rigid massless horizontal rod of length l as shown in Fig. 5.22. (a) Derive the equations of motion of the system in terms of the vertical displacement of the C.G. of the system, x(t), and the rotation about the C.G. of the system, θ(t) (b) Find the natural frequencies of vibration of the system for m1=50 kg, m2=200 kg and k = 1000 N/m.
A simplified model of a washing machine is shown. A bundle of wet clothes forms a weight wb of 20 lb in the machine and causes a rotating unbalance. The rotating weight is 40 lb (including wb) and the radius of the washer basket e is 9 in. Knowing the washer has an equivalent spring constant k = 70 lb/ft and damping ratio and during the spin cycle the drum rotates at 250 rpm, determine the amplitude of the motion and the magnitude of the force transmitted to the sides of the washing machine.
The barrel of a field gun weighs 1500 lb and is returned into firing position after recoil by a recuperator of constant c=1100 1b.s/ft Determine (a) the constant k that should be used for the recuperator to return the barrel into firing position in the shortest possible time without any oscillation, (b) the time needed for the barrel to move back two-thirds of the way from its maximum-recoil position to its firing position.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

6.13. Assuming small oscillations, derive the differential equations of motion of the two degree of freedom system shown in Fig. P6.10. Determine the response of the system, as a function of time, to the harmonic forcing function T(t).