6.35 Determine the components of theforces acting on each member of thepin-connected frame shown.D1 ftC3 ft –3 ftFE4 ftP = 2.5 kip-B2 ftAPROB. 6.35REPORT POSITIVE (+) MAGNITUDES FOR ALLVALUES

Answered: 6.35 Determine the components of the…

6.35 Determine the components of the forces acting on each member of the pin-connected frame shown. D 3 ft →+–3 ft -→ 1 ft F E 4 ft P = 2.5 kip B 2 ft A PROB. 6.35

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Related questions

Q: (6) 7. Given: The force system shown. Draw a F.B.D. of Point C and, Find the internal forces in…

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 22 kN and M…

Q: For the shown frame and loads P=972 KN and Q=1944 KN, 3 m 3 m- B 1.5 m 1 m 8 m 6 m magnitude of…

A: Given,

Q: A 175-kg utility pole is used to support at C the end of an electric wire. The tension in the wire…

A: Given, The weight of the pole = 175 kg Couple acting on the pole at Point A = Force X Perpendicular…

Q: C 4 m E 5 m 5 m 5 m 5 m A H G F 30 kN 60 kN 30 kN

Q: A truss used for supporting signs over an expressway is shown. The truss is supported by a pin at…

Q: PROBLEM 2: Determine the forces acting in all the members of the truss shown. В >3 kN 2 m 45° 30°…

Q: Practice Problem 2.4.7: Knowing that the forces P and Q are equivalent to a single force R that…

Q: 2.0 m 100 kg 2.0 m 0.5 m 15 m 1.5m The pulley at E is frictionless. Point B is a pinned connection;…

Q: Problem 5 From the given truss shown: 100 N 200 N D A В 150 N 1.5 m 3 m 1.5 m Question 13 Which of…

Q: ABCDE is supported by the ball joint at A, a bearing at E and via the BF cable, if a 100 lb C Load…

Q: The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces…

A: Given: Length of BC=180 mm=0.18 m Because angle between the BD and AD: →θ=tan-1300+100300=53.13°…

Q: For the frame and loading shown, determine the force acting on member ABC (a) at B, (b) at C.

A: Given data The force applied is F = 200 N.

Q: 9 kN A 3 m B 63.43 Determine the force in each member of the truss shown. State whether each member…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Q: Determine the forces in members BC and CG. The forces are positive if in tension, negative if in…

Q: 5.18 The 355.8-N homogeneous plate is suspended from four wires. Determine the tension in each wire.

A: As the system is in equilibrium, so all the forces must balance each other. Write the expression for…

Q: For the truss shown below it is required to locate all zero force members without calculation. 100KN…

A: The zero force member is identified by using following two conditions: 1. If three members are…

Q: y Unit: m 4.8 3.0 D 5.0 1.3 3.2 3.6 X 4.5

Q: 6.53 A Pratt roof truss is loaded as shown. Determine the force in members CE, DE, and DF. 3 kN 3 kN…

A: The free-body diagram of the truss is shown below. Here, HA denotes the horizontal reaction at A,…

Q: For the shown frame and loads P=756 KN and Q=1512 KN, P-3 m- 3 m 1.5 m 1m magnitude of y-component…

Q: 4. A truss is loaded as shown. The reactions at A and K are each 3.6 kips upward. Determine the…

A: Answer: The force in the member GH is -1.5882353 kips (Compressive).

Q: Determine the tension in cable BCD (T - N) and the horizontal (Ax - N) and vertical (A y - N)…

A: First draw the free body diagram of AB beam, As at A pin support, so Ax and Ay are developed.

Q: The beam supports two loads, w;(x) = 20x² + 100, where w, is in lb/ft and x is in ft, and a linearly…

A: Given Data: The load w1=20x2+100 and a span of 0'<x3' The linearly varying load is from 280 lb…

Q: The garden shears shown consist of two blades and two handles. The two handles are connected by pin…

A: We can see there is a symmetry about points C and D . Because of symmetry Vertical component of C,…

Q: Catenary Cable: (Different Level of Support)

A: Between two supports, the cable acts as a structural element to help sustain the weight of the…

Q: 1- Determine the force developed in the member BC and reactions at the pin support A. Take Gi = 5Kg.

A: Given data Mass (G1) = 5kg

Q: 3.2 The homogeneous beam AB weighs 400 lb. For each support condition shown in (a) through (c), draw…

A: Given data, weight w= 400 lb And this weight will be applied to the center of beam ,

Q: 6.142 A locking C-clamp is used to clamp two pieces of -in. steel plate. Determine the magnitude of…

Q: 20. A cable is subjected by two downward forces F = 3.00 kN, and P = 2.00 kN, as shown. Determine…

Q: Activity 1. Solve for the force acting on member BD, CD and CE of the Warren Truss shown using…

A: Draw the free body diagram of the truss and find the reactions: Consider the equilibrium of…

Q: 4.14 Four concurrent forces in equilibrium act at point C, a truss joint, as shown. The 15 kN force…

Q: 3.9 The homogeneous 18-kg pulley is attached to the bar ABC with a pin at B. The mass of the bar is…

Q: Q.1) (a) Draw individual free-body diagrams of the cylinder and members AB and BC shown below. Show…

A: "We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w=7 kips/ft,…

Q: For the reinforcement shown, Determine by the method of nodes the magnitude of the force on the…

A: Given data F = 321 N P = 123 N a = 2.2 m b = 1.8 m θ= 76°

Q: PROBLEM 3: Determine the tension in each of the three ropes supporting the crate. Z. 2 ft 4 ft 4 ft…

Q: 60k 5 ft 30 k 5 ft IC 5 ft 5 ft 20 ft 20 ft

Q: A force P is applied to a bent rod that is supported by a roller and a pin and bracket. For each of…

Q: A 600-lb horizontal force is applied to pin A of the frame shown. Determine the forces acting on the…

A: ∑Fy=0Fy-Ey=0........1∑Fx=0 Fx-Ex+600=0...........2 ∑ME=0 Fy(6)-600(10)=0 Fy=1000 lb Putting value…

Q: 10 ft Using the figure below, determine the forces in the members of the truss and the reactions at…

Q: Determine the value of the force in bar AB c the truss shown (N without decimals), enter a positive…

A: Given data:- b= 4m c = 3.5m a = 3m P1 = 600N P2 = 400N

Q: A 150-lb cylinder is supported by two cables AC and BC that are attached to the top of vertical…

A: The free body diagram is shown below, The coordinate of point A is given as, A=-10.8,15,0 The…

Q: Q2) For the truss shown below determine the internal forces of member BE and AB. 200N 30° H 50N 100…

Q: 4. For the frame below, determine the forces acting on member AFGH. 0.8 m 1 m 0.5 m, 0.5 m, 0.25 m…

Q: Consider one end of a timber roof truss that is supported on a masonry wall. The reaction at the…

A: For the given condition,∑Fx=0F2cos25=F1F1=7cos25 kNF1=6.34

Q: 6. Determine the force in BE of the truss shown. Indicate whether the member is in tension or…

Q: 4/1 Determine the force in each member of the simple equilateral truss. Ans. AB = 736 N T, AC = 368…

Q: For the frame and loading shown, determine the internal forces at the point indicated:Point K

Question

6.35 Determine the components of the
forces acting on each member of the
pin-connected frame shown.
D
1 ft
C
3 ft –3 ft
F
E
4 ft
P = 2.5 kip
-B
2 ft
A
PROB. 6.35
REPORT POSITIVE (+) MAGNITUDES FOR ALL
VALUES

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A truck has a mass of 4820 kg and a wheelbase (distance between front and rear wheels) of 4.8 m. Ifthe center of mass of the truck is located 1.9 m behind the front wheels, where should a 5450 kg load beplaced (relative to the front wheels) in order to have equal weight on both sets of wheels?
Determine the unknown forces by applying d’alemberts principle to a free body.
Suppose P = 2500 lb. From the frame below, determine the magnitude and direction of (1) Ax and Ay (2) Dx and Dy (3) the vertical and horizontal component of the force at C as it acts on member BCD
The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1 and T2 is a vertical 3200-lb force, determine T1 and T2.
A loaded truck is transmitting 10 kN pressure on each wheel. The centre of gravity of the loaded truck is 1·2 m above the road level and the centre to centre distance of wheels is 2 m. Find the pressure exerted by the inner and outer wheels, when the truck is going round a curve of 440 m radius at 48 km.p.h.
What is the mass supported as shown, when the torque created by an axis at position A is 1800 mN?
A 5-m long simply supported timber beam carries two concentrated loads as shown. If L = 16 KN and M = 54 kN, determine the magnitude of the vertical force acting at support D.
The normal distributed load is applied on the circular beam. Question: The resultant force caused by the distributed load on the beam
An 8-m long cantilever beam is loaded with vertical forces A = 60 kN and B = 108 kN, separated by a distance d = 5.6 m, as shown. Replace the two forces with a single equivalent force R and determine the distance x-bar (x¯) from the left end of the beam to the line of action of R.
A 10-m uniform beam of weight 100 N is supported by two ropes at its ends. If a 400-N person sits at the center of the beam, what is the tension in the right rope?
Determine the magnitude T of the tension in the supporting cable for the jib crane shown. The beam AB is a standard 0.5 meter l-beam weighing 5.5 kN.
9) As shown by this image, the 89-lb crate is supported by three ropes as shown. The coefficients in the coordinates are a=4.1, b=3.6, and c=7.3. Determine the tension force in cable OA, in lb. 10) As shown by this image, the 87-lb crate is supported by three ropes as shown. The coefficients in the coordinates are a=4.7, b=3.8, and c=7.1. Determine the tension force in cable OC, in lb.