Answer 6.61 we-PROBLEMS 6.58, 6.59, 6.606.61 Water (at 50 F) flows through this nozzle at a rate of 15 cfstheand discharges into the atmosphere. DDetermine the force required at the flange to hold the nozzle inss-12 in., and D, =9 in.place. Assume irrotational flow. Neglect gravitational forces.6.62 Solve Prob. 6.61 using the following values: ) =0.30 m/s,D=30 cm, and D,10 cm. (p 1000 kg/m)m.nalde-In-a onPROBLEMS 6.61, 6,62pli-6.63 This "double" nozzle discharges water (p 62.4 lbm/ft')hring

Answered: Image /qna-images/answer/363d3ee5-bc28-4fbb-8524-3ee0448c85ed.jpg

6.61 Water (at 50°F) flows through this nozzle at a rate of 15 and discharges into the atmosphere. D Determine the force required at the flange to hold the nozzle place. Assume irrotational flow. Neglect gravitational forces. 6.62 Solve Prob. 6.61 using the following values: Q=0.30 m D=30 cm, and D,= 10 cm. (p 1000 kg/m) , = 12 in., and D, =9 %23

6.61 Water (at 50°F) flows through this nozzle at a rate of 15 and discharges into the atmosphere. D Determine the force required at the flange to hold the nozzle place. Assume irrotational flow. Neglect gravitational forces. 6.62 Solve Prob. 6.61 using the following values: Q=0.30 m D=30 cm, and D,= 10 cm. (p 1000 kg/m) , = 12 in., and D, =9 %23

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B Refer to, Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be frictionless in the siphon. Find the rate of discharge in mºls and the pressure head at B if the pipe has a uniform diameter of 150 mm. M Tar N
In a certain hydraulic turbomachine, the following data apply:Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s.At the exit, V2 is purely axial and has a value of 14 m/s, and blade speed is9 m/s. Is this power absorbing or power producing? Find E and the changes instatic and stagnation pressures. Would this machine be classified as a purelyradial, purely axial, or mixed flow type?Ans: E=420 J/kg; Δpstag=420 kPa; Δpstat=247.4 kPa
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
Water flows through a horizontal 150 − ?? pipe under a pressure of 414 ???. Assuming no losses, solve for the flow if the pressure at a 75 − ?? diameter reduction is 138 ???
It is desired to pump 50 ft3/s of water at a speed of 22 r/s,against a head of 80 ft. (a) What type of pump would yourecommend? Estimate (b) the required impeller diameterand (c) the brake horsepower.
Properties of jet obtained from orifice, from notches, from weirs
Air flows isentropically through the channel To = 310 ° C. both ends have identical area that is A = 25 cm², pressure p1 = 160 kPa and p2 = 65 kPa. Determine a). Mass flow rate b). Throat area and C). Ma2
A 75mm diameter orifice discharges 26 L/s of liquid under a constant total producing head of 3m. The diameter of the jet of the vena contracta was measured using a digital caliper and it reads 66.5mm. Calculate the coefficient of velocity.
The MITL ME laboratory has installed a double-suction, three-stage, centrifugalpump with a discharge of 330 gpm under 200 ft head and running at 1200 rpm. It isproposed to install another pump with double suction and six stages, but of the samecharacteristics, to operate at 98 ft head and deliver 430 gpm. Calculate a) the speed ofthe proposed pump; b) the impeller diameter of the proposed pump if the diameter of theexisting pump is 6 inches; and c) the type of the existing and the proposed pump.
In Fig. there are 125 ft of 2-in pipe, 75 ft of 6-inpipe, and 150 ft of 3-in pipe, all cast iron. There are three90° elbows and an open globe valve, all flanged. If the exitelevation is zero, what horsepower is extracted by the turbinewhen the flow rate is 0.16 ft3/s of water at 20°C?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
The pipe bend of Fig. has D 1 = 27 cm and D 2 =13 cm. When water at 20 ° C fl ows through the pipe at 4000gal/min, p 1 =194 kPa (gage). Compute the torque requiredat point B to hold the bend stationary.