Elevation 100 ft 2 in Open globe Turbine 6 in 3 in

Q: )Water 10°c flows down through a 53.13 deg, nclined, converging pipe section as shown. The fiow…

A:

Q: Include a free body diagram A fire pump delivers water through a 15 cm main pipe to a hydrant to…

A:

Q: The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and…

A:

Q: Q1. The pump with 96.52 cm in diameter characteristics shown in figure below is used to pump water…

A:

Q: A 70 percent efficient pump delivers water at 20°C fromone reservoir to another 20 ft higher, as in…

A: The data given is,

Q: A mine ventilation fan, running at 295 r/min, delivers500 m3/s of sea-level air with a pressure rise…

A: Write the formula for pressure drop in terms of the head. Here,  is the pressure rise, H is the…

Q: The spiral conical draft tube are connected to Francis turbine. The diameters of the internal and…

A:

Q: Three pipoes A,B and C coonected in seies discharges 160 L/s of water. The properties of pipe: for…

A:

Q: 0.60 m lighest water level Lowest water level 21.0 m 1.5 m 672.00 m E Dacil + Water will be…

A: Q=3790  LminQ=3790×10-360Q=.0631 m3secVs=1.5 msec,vb=3…

Q: 3.6 A Pelton wheel develops 740KW under a head of 310 m. Find the jet diameter if its efficiency is…

A:

Q: A Pelton wheel works at the foot of a dam because of which the head available at the nozzle is 400…

A:

Q: : The pipe flow in Fig. 2 is driven by pressurize eded to provide water flow rate Q =75 m³/h?. T…

A:

Q: The 32-in pump in Fig.  is used at 1170 r/min in asystem whose head curve is Hs (ft) = 100 + 1.5Q2,…

A: Given data: Diameter of pump, D = 32 in. Suction head =  Hs (ft) = 100 + 1.5Q2   Let, Density of…

Q: The single stage, axial flow turbomachine shown in figure 3 involves water flow at a volumetric…

A:

Q: A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation…

A:

Q: Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe, the…

A:

Q: The impacting jet for a Pelton turbine carries a flow of 0.5 m/s, and the jet is 7 cm in diameter.…

A: Given : Q = 0.5 m3/s d = 7 cm To find : Pressure of the fluid on impeller

Q: Elevation = ? reservoir on the right at a rate of 0.45 m/s. The formula for the head losses in the…

A:

Q: The waterwheel in Fig.  is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet…

A: Given data: The speed of the water wheel is, N = 200 r/min. The velocity of the jet is, Vj = 150…

Q: 6.62 Water at 20°C is to be pumped through 2000 ft of pipe from reservoir 1 to 2 at a rate of 3…

A:

Q: Two 35-inch pumps from the figure (a) shown below are installed in parallel for the system of the…

A:

Q: A Pelton turbine having 1.6 m bucket diameter develops a power of 3600 kW at 400 rpm under a net…

A:

Q: data apply: Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s. At the exit, V2 is purely axial…

A:

Q: A centrifugal pump developing 9 ft head at 1200 rpm is driven by a 3 hp motor. Impeller diameter is…

A:

Q: A Kaplan turbine produce (9 MW) under a head (7.5 m). Assume a speed ratio of (2) flow ratio (0.75)…

A:

Q: llustration 10.7 A covered, baffled vessel, 0.5 m (19.7 in) diameter, 0.5 m deep is to be used for…

A:

Q: Air at atmospheric pressure and at 25°C enters a centrifugal blower when the rotor is spinning at…

A:

Q: PROBLEM: 1. A boiler feed pump delivers water at 100 °C which it draws from an open hotwell with a…

A: As per rules solved 1 problem only

Q: An orifice on vertical wall has a head of 1.13m of oil ( sp.gr.=0.89). It discharges 6192N of oil in…

A:

Q: Q3) Kaplan turbine A) The runner of Kaplan turbine working under dsitance of (5.5m) to produce (9…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: An acceptance test was conducted on a centrifugal pump having a suction pipe 25.4 cm in diameter and…

A:

Q: Q 5: A convergent - divergent mouthpiece is fitted to the side of a tank. The discharge through…

A:

Q: The plunger diameter of a single acting reciprocating pump is 115 mm and the stroke is 230 mm. The…

A: Given: The diameter of the plunger is: D=115 mm=0.115 m The length of the stroke is: L=2r=230…

Q: A Francis radial-flow hydroturbine is being designed with the following dimensions: r2 = 2.00 m, r1…

A: Given, A Francis radial-flow hydroturbine with the following dimensions:r2 = 2.00 m, r1= 1.42 m, b2…

Q: Calculate the available net positive section head NPSH in a pumping system if the liquid density p…

A:

Q: For a single stage impulse turbine: Rotor diameter= 1 m Speed%3D 2500 rpm Nozzle angle= 20°…

A: GIVEN DATA- NOZZEL ANGLE =20' DIAMETER D=1m SPEED N=2500rpm

Q: 32. The external and internal diameters of an inward flow reaction turbine are 60 cms and 30 cms…

A:

Q: At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters…

A:

Q: The pressure drop across a turbine is 200kPa. The flow rate is 0.25m3/min. WHat is most nearly the…

A:

Q: /Suppose there are three identical pumps in series, each producing 1500 ft of the head at flow rate…

A: A Pump is an instrument that usually translates fluids (liquids or gases) or slurries from electric…

Q: 4. Find the head loss in a pipeline consisting of 200 ft of 4-in steel pipe, a 90° bend on 24-in…

A: Solution

Q: Assume that 57 L/s of oil SG = 0.86 is pumped through a 300 mm diameter pipeline of cast iron. If…

A: Volumetric flow rate of oil, Q=57 L/s=0.057 m3/sSpecific gravity of oil, SGo=0.86Diameter of pipe,…

Q: Q 5: A convergent - divergent mouthpiece is fitted to the side of a tank. The discharge through…

A:

Q: In the figure shown below there are 125 ft of 2-in pipe, 75 ft of 6-in pipe, and 150 ft of 3-in…

A:

Q: Two water tanks, each with base area of 1 ft2, are connectedby a 0.5-in-diameter long-radius nozzle…

A: For water at 20oC, take density as  1.94 slug/ft3 and viscosity   2.09x10-5 slug/ft.s. For a…

Q: 1. A Pelton wheel of 4 m diameter operates with a head of 1000 m. Estimate the flow rate and power…

A: Solution    Calculate the flow rate          v=2gh=2×9.81×1000=140 msQ=Av=π4×42×140=1759 m3s

Q: In the figure, the pipe entrance is sharp-edged. If the flow rate is 0.004 m/s, what power, in W, is…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.