6.85 (WILEY The two-dimensional velocity field for an incompress- ible Newtonian fluid is described by the relationship V = (12xy – 6x)î + (18x²y – 4y°)ĵ - where the velocity has units of m/s when x and y are in meters. Determine the stresses o , 0yy, and Ty y = 1.0 m if pressure at this point is 6 kPa and the fluid is glycerin at 20 °C. Show these stresses on a sketch. at the point x = 0.5 m,

6.85 (WILEY The two-dimensional velocity field for an incompress- ible Newtonian fluid is described by the relationship V = (12xy – 6x)î + (18x²y – 4y°)ĵ - where the velocity has units of m/s when x and y are in meters. Determine the stresses o , 0yy, and Ty y = 1.0 m if pressure at this point is 6 kPa and the fluid is glycerin at 20 °C. Show these stresses on a sketch. at the point x = 0.5 m,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
In a stream of glycerine in motion, at a certain point the velocity gradient is 0.25 meter per sec per meter. The mass density of fluid is 1268.4 kg per cubic meter and kinematic viscosity is 6.30 x 10^-4 square meter per second. Calculate the shear stress in Pascal at the point.
A Newtonian fluid with absolute viscosity (Greek mu) flows past a flat surface. Due to the no-slip boundary condition, the velocity profile, u(y), develops near the surface and is given by u/U (shown in image provided) where the constant parameters U and delta have dimensions of velocity and length respectively.a) Develop an expression for the shear stress acting in any horizontal plane.b) Determine the shear stress acting on the surface at y = 0 and again at the edge of the boundarylayer, y = delta. (Express your answers in terms of Greek mu, the outer velocity U, and the boundary layer thickness delta.)
choose the correct answer 3- when the flow is happened without change in its quantity or velocity with time , then the flow is: * a) Unsteady b) Uniform c) Steady d-None of all above 4- Reynolds number represents: * a) Viscosity force to inertia force b) Inertia force to viscosity force c) Equality between inertia and viscosity forces d-None of all above
A fluid has a dynamic viscosity of 0.5 poise. Calculate the velocity gradient and the maximum intensity of shear stress at the boundary, if the fluid is filled between two parallel plates 5 cm apart and one plate is moving at a velocity of 1ms and the other plate is stationary. Assume that distribution of velocity is v=100-k(5-y)².
Water flowing at 1.0 ft/s in a pipe passes into a constriction where area is one-tenth the normal pipe area. What is the decrease in water pressure in the constriction? The weight density of water is 62.4 lbs/ft3.
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
Crude Oil is flowing through a circular pipe with a centerline velocity of 0.5m/s at a temperature of 60 degrees Celcius and viscosity of 5.5 mPa s. Determine the shear stress at the pipe surface if a parabolic velocity distribution is assumed. Also, indicate the kinematic viscosity of the crude oil at the given temperature. The density of the crude oil is 855 km/m^3 and the pipe diameter is 20 mm.
Find the kinematic viscosity of an oil having density of 980kg/m^2 when at a certain point in the oil, the shear stress is 0.25 Pa and the velocity gradient is 0.3 m/s.
What is the kind of stress applied on the illustration which has caused the fluid to create a velocity profile? a. Shear Stress b. Normal Stress c. Friction