6/110 The unbalanced wheel has a mass of 10 kg and rolls 40 mm 4, without slipping on the horizontal surface. When the mass center G passes the horizontal line through O as shown, the angular velocity of the wheel is 2 rad/s. For this instant compute the nor- mal foree N and friction force F acting on the wheel at its point of contact with the horizontal surface. The wheel has a radius of gyration about its mass center of 64 mm. 100 0 mm Problem 6/110

6/110 The unbalanced wheel has a mass of 10 kg and rolls 40 mm 4, without slipping on the horizontal surface. When the mass center G passes the horizontal line through O as shown, the angular velocity of the wheel is 2 rad/s. For this instant compute the nor- mal foree N and friction force F acting on the wheel at its point of contact with the horizontal surface. The wheel has a radius of gyration about its mass center of 64 mm. 100 0 mm Problem 6/110

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The uniform slender bar of mass m and total length L is released from rest in the position shown. Determine the force supported by the small roller at A and the acceleration of roller A along the smooth guide, Evaluate your results for theta = 15 degree.
6/40 If the frictional moment at the pivot O is 2 N-m, de- termine the angular acceleration of the grooved drum, which has a mass of 8 kg and a radius of gyra- tion ko = 225 mm.
The shown spool has a mass of 100 kg and radius ofgyration of 0.3 m. For P = 70 N and ms =mk = 0.2 thespool rolls without sliding, calculate the angularacceleration of the spool
The racing vehicle has a mass of 750 kg and center of mass in G. If there is no slippage, determinate the normal reaction, in Newtons, presented on each of the front wheels in A, when an acceleration of a = 6.4 m/s².
The uniform slender beam has a total mass of M and rotates freely at the indicated suspension point O. The horizontal beam section has a length of 2/3L and the vertical section has a length of 1/3L. The beam is released from the drawn position a) Draw the full-body diagram.b) Draw the kinematic diagram.c) determine the centre of gravity of the beamd) set up the necessary motion equationse) determine the angular acceleration of the beam (in g/L)f) determine the resulting force in the suspension point O. (leave the mg terms)
The right‐angle plate is formed from a flat plate having a mass ρ per unit area and is welded to the horizontal shaft mounted in the bearing at O. If the shaft is free to rotate, determine the initial angular acceleration α of the plate when it is released from rest with the upper surface in the horizontal plane. Also determine the y‐ and z‐components of the resultant force on the shaft at O.
The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
If P = 30 lb, determine the angular acceleration of the 50-lb roller. Assume the roller to be a uniform cylinder and that no slipping occurs
The wheel has mass m and centroidal radius of gyration (k bar) and rolls without slipping up the incline under action force P. The force is applied to the end of a cord which is wrapped securely around the inner hub of the wheel as shown. Determine the speed Vo of the wheel center O after the wheel center has traveled a distance d up the incline. The wheel is at rest when the force P is first applied.
The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction; a) The time elapsed until the angular velocity of gear B reaches 600 rpm.b) Find the tangential force from gear B to gear A.
The vertical bar AB has a mass of 150 kg with center of mass G midway between the ends. The bar is elevated from rest at θ = 0 by means of the parallel links of negligible mass, with a constant couple M = 5 kN∙m applied to the lower link at C. Determine the angular acceleration α of the links as a function of θ and find the force B in the link DB at the instant when θ = 30°.
Each of the two links has a mass of 2 kg and a centroidal radius of gyration of 60mm. The slider at B has a mass of 3 kg and moves freely in the vertical guide. The springhas a stiffness of 6 kN/m. If a constant torque M = 20 N∙m is applied to link OA throughits shaft at O starting from the rest position at θ = 45°, determine the angular velocity ofOA when θ = 0.