Qs1 The wheel of metor Cy cle and the engine parts haveanoment of inertia 2-5 kg.m? and o 15 kg.m? respectively Theaxis of rotation of the engine erank Shaft is parallelto that of the road whels-If the gear ratio is5:1 and the diameter of the read wheels is o.65 m,find the magnitude and direction of the gyroscopicCouple when the motor Cycle rounds a eurve of 3omradius at 16 m/s.

Answered: Image /qna-images/answer/559c1c5b-6050-4aa8-9636-a5805271df5d.jpg

Q5/ The wheel of mutor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o15 kg.m? respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter of the road wheels is o.65 m, find the magnitude and divection of the gyroscopic Couple when the motor Cycle rounds a eurve of 3om radius at 16 m/s.

Q5/ The wheel of mutor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o15 kg.m? respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter of the road wheels is o.65 m, find the magnitude and divection of the gyroscopic Couple when the motor Cycle rounds a eurve of 3om radius at 16 m/s.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

The equation of the turning moment diagram for the three crank engine is given by: T(N.m) =25000 - 7500 sin 3theta where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?
A constant torque of 2kN-m is exerted on a crankshaft to start the engine.The flywheel has a mass of 1800kg and a radius of gyration 1m .If there is a resisting torque of 1kN-m,find the speed of the engine after 1 minute.
ower shaft running at a steady speed of 175 rev/min driy 8 single-plate friction clutch of external and intern mm respectively. The masses on the countershaft have £ 250 mm and a total mass of 350 kg. The axial spring I 198 450 N, and 4 = 0-3. Assuming uniform acceleration guired to reach full speed from rest, and the work dissipad during that time. (U. Lond.) (Ans. : 99 g
A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
A gear engine automobile is traveling along a curved track of 120m radius. Each of the four wheels has a moment of inertia of 2.3 kg m2 and an effective diameter of 600 mm. The rotating parts of the engine have a moment of inertia of1.25kg m2 the gear ratio of the engine to back wheel is 3:2.The engine axis is parallel to the gear axle and the crank shaft rotates in the same sense as the road wheels. The mass of the vehicle is 2050 kg and the center of mass is 520 mm above the road level. The width by the track is 1.6m, what will be the limiting speed of the vehicle if all the four wheels maintain contact with the road surface (b) Explain the function of a flywheel from a crank effort diagram.
A single cylinder horizontal engine runs at 120 r.p.m. The length of stroke is 400 mm. The mass of the revolving parts assumed concentrated at the crank pin is 100 kg and mass of the reciprocating parts is 150 kg. Determine the magnitude of the balancing mass required to be placed opposite to the crank at a radius of 150mm which is equivalent to all the revolving and 2/3rd of the reciprocat- ing masses. If the crank turns 30° from the inner dead centre, find the magnitude of the unbalanced force due to the balancing mass.
An engine of a motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiencyof the differential and transmission is 75% with an over-all speed reduction to. 1 determine he torque to bedelivered by the clutch N-m.
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
Illustrate the force-inertia diagram Describe the relationship between the angular accelerations of gears A and B? Which of the following equations used to solve the problem is INCORRECT?
Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb. a. 50 Btu b. 50 Btu c. 30.50 Btu d. 51.50 Btu