6/21 The homogeneous rectangular plate weighs 40 lb and is supported in the vertical plane by the light parallel links shown. If a couple M = 80 lb-ft is applied to the end of link AB with the system initially at rest, calculate the force supported by the pin at C as the plate lifts off its support with 0 = 30°. 24" VAnswer C = 46.3 lb 16" 16" e 16" PROBLEM 6/21 M

6/21 The homogeneous rectangular plate weighs 40 lb and is supported in the vertical plane by the light parallel links shown. If a couple M = 80 lb-ft is applied to the end of link AB with the system initially at rest, calculate the force supported by the pin at C as the plate lifts off its support with 0 = 30°. 24" VAnswer C = 46.3 lb 16" 16" e 16" PROBLEM 6/21 M

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.11P: The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the...

See similar textbooks

Similar questions

A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 710 kg and an average gear-tooth force of 2.75 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset x¯ of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers.Assume r = 140 mm, R = 515 mm, θ= 25°.
If the speed of the shaft, as shown in Figure 1 below, is 220 rev/min, calculate the magnitudes and orientations of the bearing reactions at A and B for the two-mass system. Given a = b = 250 mm, c = 50 mm, R1 = 60 mm, R2 = 40 mm, m1 = 2 kg, and m2 = 1.5 kg.
a trolley of mass m stands on frictionless rails.a rod of mass m and length l is pivoted to the roof of trolley on a frictionless hinge and the and rod is gently left from the horizontal postion as shown in the figure. initialy the whole system was at rest when the rod becomes vertical for the first time.net vertical force offered by the track to the carriage is 16/x mg. find x.
Please provide complete solutions and illustrations for the problem below. The bent bar shown in the figure weighs 24kg/m and is free to rotate in a vertical plane about a horizontal axis at A. Compute the X & Y components of the bearing reaction at A an instant after it is released from rest at the given position.
The 15-kg uniform steel plate is freely hinged about the horizontal z-axis. Calculate the force supported by each of the bearings at A and B an instant after the plate is released from rest while in the horizontal position shown. The mass MOI of the triangle about the z-axis is Iz=1/6mh2
A man pushes bar CD to either initiate uphill motion of the homogeneous spool or to just keep the homogeneous spool from moving downhill. The spool has mass M = 88 kg. .If slippage first occurs at B, calculate the smallest force P in N that the man must apply to the bar CD to prevent the spool from moving downhill.
the table lamp consists of two uniform arms, each weighing 4N, and a 10 N bulb fixture. if angle is 16 degrees calculate the couple CAthat must be supplied by the friction in joint A.
The force F of 250 N is applied because a block with a mass of 20 kg and a radius of inertia of 160 mm as shown in the figure. This force lifts the weight B of 10 kg. Calculate the pulley angular acceleration and the normal acceleration of weight B, tension in the cable and reaction in the pulley bearing.
The figure is a model for member CDE of the frame described in Prob. 4.10. Draw the FBD of the member, neglecting its weight. Count the unknowns.
A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a circle with center at O.The channel is frictionless and sits on a horizontal table top.The figure shown is the top view.Which of the following force(s) are acting on the ball when it is within the frictionless channel at position B? Explain your answers.Check all that apply.1- A downward force of gravity.2- A force pointing from O to B.3- A force in the direction of motion.4- A force pointing from B to O.
A man pushes bar CD to either initiate uphill motion of the homogeneous spool or to just keep the homogeneous spool from moving downhill. The spool has mass M = 88 kg. If slippage first occurs at B, calculate the smallest force P in N that the man must apply to the bar CD to initiate uphill motion of the spool.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?