Problem 9.38 The steel pipe in (Eigure 1) has an inner diameter of 4.38 in, and an outer diameter of 4.63 in. Figure 12 in. 12 in.. 130 1 of 1 60 lb Part A If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A. which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. 1961 ΑΣΦ. 11 vec 010338.6.-17.11 Submit Previous Answers Request Answer Review X Incorrect; Try Again: 8 attempts remaining ? psi,

Problem 9.38 The steel pipe in (Eigure 1) has an inner diameter of 4.38 in, and an outer diameter of 4.63 in. Figure 12 in. 12 in.. 130 1 of 1 60 lb Part A If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A. which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. 1961 ΑΣΦ. 11 vec 010338.6.-17.11 Submit Previous Answers Request Answer Review X Incorrect; Try Again: 8 attempts remaining ? psi,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
Show whether it is safe by calculating the stresses at point A according to the Tresca Criteria. (Diameter: 20 mm, σA = 320 MPa)
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
A cylindrical steel pressure vessel has an inner radius of 24 inches and wall thickness of 0.25 inches. Determine the tangential and longitudinal stresses when the vessel is pressurized to 125 psi.
Problem No. 1 A standpipe with an inside diameter of 108 in. contains water, which has a weight density of 62.4 lb/ft3. The column of water stands 30 ft above an outlet pipe, which has an outside diameter of 6.625 in. and an inside diameter of 6.065 in. (a) Determine the longitudinal and hoop stresses in the outlet pipe at B. (b) If the maximum hoop stress in the standpipe at point A must be limited to2,500 psi, determine the minimum wall thickness that can be used for the standpipe.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
A thick cylinder internal diameter 240mm external diameter 240mminternal diameter ‘D’ is subject to external pressure of 40MPa. Determine the diameter‘D’ if the minimum hoop stress in the cylinder is not to exceed 200MPa in mm.
A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm. it fits without clearance in an 80-mm hole in a rigid block. The tube is then subjected to an internal pressure of 4.00 MPa. Assuming v=1/3 and E= 83 GPa, determine the tangential stress in the tube.
The steel pipe in (Figure 1) has an inner diameter of 3.41 in and an outer diameter of 3.66 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe.
!! Show Complete & Detailed Solution w/ FBD !!From the figure shown, the diameter of each segment is indicated. Determine the average normal stress developed at points.a. Ab. Bc. C.