-6i - 20 10in- laminate substrate Fig.2 Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 lb vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate.

-6i - 20 10in- laminate substrate Fig.2 Q2: The tool shown in Fig.2 is used in a gluing operation to press a thin laminate to a thicker substrate. If the wheels at points A and B both have 2 in diameter and have frictionless bearings, and a 20 lb vertical force to the handle of the tool, determine the forces applied to the top of the laminate and the bottom of the substrate.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

Draw the FBD of the entire frame, assuming that friction and the weights of the members are negligible. How many unknowns appear on this FBD?
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a diameter of 8 in. If a force of 120 lbs is applied to the small piston, what is the force on the large piston, neglecting friction.
In the above system with frictionless pulleys, 45 lb and W weights are hung on both sides. What must the weight W be in order for the 300 lb block to overcome the μ friction force and move on?
A 100-m, 10 N uniform rods carries 20-N and 30-N weights suspended at its ends, as shown. Where would the fulcrum be placed to balance the rod?
body resting on a rough horizontal plane requires a pull of 300 N inclined at 40º to the horizontal plane just to move it. It is found that a push of 150 N inclined at 40o to the x-axis can also make the body to move. Determine the weight of the body and the coefficient of friction.
Block A weighing 6 kN rests on a horizontal plane and supports on top of it another block of weight 1 kN as shown in Fig. 11-(i). Block B is attached to a vertical wall by an inclined string which makes an angle of 30o with the horizontal. What should be the value of horizontal force P to cause the motion of the lower block to impend? Take μ=0.30 for all the surfaces.
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
A 150lb man stands on a 60lb bar to which a cable is fixed at B. The cable passes over two fixed pegs with coefficients of friction indicated. Assume that the arrangement of the pegs permits the cable to contact each peg over a total angle of 90-degrees (90-degrees per peg). Assume that the normal force exerted by the man on the bar acts downward through A. Find the largest force the man can exert on the cable and maintain the bar horizontal.
17. A 430-kg block is resting on a 27 deg inclined plane with a coefficient of friction = 0.64. Find the required horizontal force P (in kN) that is necessary to start the block UP the incline. Round off to two decimal places.
A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A (on the ground). The angle of friction at all contact surfaces is 21.8°. Find the smallest angle 0 at which the ladder can be inclined with the horizontal before it is on its verge of slipping.