7-2 forms of the instantaneous signal phase and frequency.7-2A function generator can be angle modulated with variouswaveforms. Based on a 50-Hz sinusoid before modulationis applied, the output signal with modulation isv(t) = 20 cos(100nt + 6nt)Determine (a) instantaneous signal phase and (b) instanta-neous signal frequency (radian and cyclic). (c) Sketch theforms of the instantaneous signal phase and frequency.

Modulation- Changing some parameter of the carrier signal with respect to the modulating signal is…

7-2 A function generator can be angle modulated with various waveforms. Based on a 50-Hz sinusoid before modulation is applied, the output signal with modulation is v(1) = 20 cos(100t + 6mt) Determine (a) instantaneous signal phase and (b) instanta- neous signal frequency (radian and cyclic). (c) Sketch the forms of the instantaneous signal phase and frequency.

7-2 A function generator can be angle modulated with various waveforms. Based on a 50-Hz sinusoid before modulation is applied, the output signal with modulation is v(1) = 20 cos(100t + 6mt) Determine (a) instantaneous signal phase and (b) instanta- neous signal frequency (radian and cyclic). (c) Sketch the forms of the instantaneous signal phase and frequency.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem ECSQ

See similar textbooks

Similar questions

How the phase modulation can generate frequency modulation?
With the aid of diagrams, show and explain how phase locking is used to: demodulate a frequency-modulated (FM) signal. generate a range of frequencies from a single stable frequency source. synchronise an undersampled signal to the carrier frequency.
Problem1: the figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: 1. What is the modulation scheme in A? 2. What is the modulation scheme in B? 3. What is the sampling frequency? 4. What is the value of the duty cycle in A?
A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Ω antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM.
A 10Vp carrier signal is amplitude modulated by two different frequencies 5 KHz and 10 KHz with amplitude of 4Vp and 7.5Vp respectively using an DSBFC. If the system is connected to the 100Ω antenna, (a) what is the modulated carrier power and AM wave total power? From DSBFC, different transmitters with different modulation schemes were used to evaluate the performance in terms of power and bandwidth and compare to conventional AM. (b) Complete the table below and provide your solution.
An AM signal as shown below. The carrier frequency is 600 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y-axis is the amplitude of the AM signal. Answer the following questions with appropriate solution if applicable. Determine the type of AM signal in the figure. Determine the frequency of the message signal in Hz. If the peak voltage level of the modulating signal and carrier are 1V and 2V respectively, determine the modulating index. Determine the power of the unmodulated carrier in W. Assume the load resistance to be 1-ohm. Determine the power of sidebands in W. Determine the total power of the AM signal in W.
What is the effect of value of filter capacitor on ripple voltage?
The figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: What is the quantization noise in a modulator that uses a 4-bits register for the analog to digital conversion of the given sinusoidal signal? Please give deatiled solution for good understanding
Subject - Design electrical circuits for single-phase AC networks Question Discuss the difference between resonant and nonresonant circuits
1. How many sinusoidal frequency components are there for a perfect switching square waves? 2. What is the frequency of the fundamental ac sinusoidal component of a square wave with period 10usec?
An AM signal is provided below. The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y-axis is the amplitude of the AM signal. Answer the following questions with appropriate solutions if applicable. Determine the type of AM signal in the figure. Determine the frequency of the message signal in Hz. Determine the peak voltage level of the carrier in V. Determine the peak voltage level of the modulating signal in V. Determine the modulating index. Determine the power of the unmodulated carrier in W. Assume the load resistance to be 1-ohm. Determine the power of sidebands in W.
Derive the frequency reuse factor for a triangular cell