7-70. The assembly consists of three disks A, B. and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d, within the support space, and the diameter dz of the hole in the bottom disk. The alowable bearing stress for the material is (a.) - 350 MPa and allowable shear stress is Tal - 125 MPa. 140 kN mm 10 mm

7-70. The assembly consists of three disks A, B. and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d, within the support space, and the diameter dz of the hole in the bottom disk. The alowable bearing stress for the material is (a.) - 350 MPa and allowable shear stress is Tal - 125 MPa. 140 kN mm 10 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The observation cage C has a weight of 250 kip and through a system of gears, travels upward at constant velocity along the A-36 steel column, which has a height of 200 ft. The column has an outer diameter of 3 ft and is made from steel plate having a thickness of 0.25 in. Neglect the weight of the column, and determine the average normal stress in the column at its base, B, as a function of the cage’s position y. Also, determine the displacement of end A as a function of y.
Determine the greatest constant angular velocity v of the flywheel so that the average normal stress in its rim does not exceed s = 15 MPa. Assume the rim is a thin ring having a thickness of 3 mm, width of 20 mm, and a mass of 30 kg>m. Rotation occurs in the horizontal plane. Neglect the effect of the spokes in the analysis. Hint: Consider a free-body diagram of a semicircular segment of the ring. The center of mass for this segment is located at rn = 2r> from the center.
The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress in the rod at a section located at B due to the rod’s weight.
The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine the force P applied to the plate and the distance d to where it is applied.
The 3/4-in.-diameter shaft is subjected to the loading shown. Determine the stress components at point A. Sketch the results on a volume element located at this point. The journal bearing at C can exert only force components Cyand Cz on the shaft, and the thrust bearing at D can exert force components Dx, Dy, and Dz on the shaft.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the bolt is subjected to a compressive force of P = 20 kN, determine the average normal stress in the steel and the bronze. Est = 200 GPa, Ebr = 100 GPa.
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi
The drill pipe has an outer diameter of 75mm, a wall thickness of 10mm, and a weight of 70 kg/m. If it is subjected to a torque and axial load as shown, determine at a point on its outer surface at section a (a) the principal stress and planes and (b) the maximum in-plane shear stress, average stress and its plane.
The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is limited to 100MN/m2.b) Determine the diameter of the pin located at C if the shear stress is limited to 70 MN/m2.c) Determine the crushing force in the support plates in C with a thickness of 6mm.
The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. Determine the average normal stress in the aluminum and the steel due to this loading. The pipe has an outer diameter of 80 mm andan inner diameter of 70 mm.
The 150 mm by 150 mm block of aluminum supports a compressive load of 6 kN. Determine the average normal and shear stress acting on the plane through section a–a. Show the results on a differential volume element located on the plane.
The short concrete cylinder having a diameter of 50 mm is subjected to a torque of 500 N # m and an axial compressive force of 2 kN. Determine if it fails according to the maximum normal stress theory. The ultimate stress of the concrete is sult = 28 MPa.