7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF

7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.16MCQ

See similar textbooks

Similar questions

A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of power. With VS=1. per unit, VR=0.9 per unit, =5000 km, Zc=500, and =36.87, determine a nominal voltage level for the lossless transmission line based on Eq. (5.4.29) of the text. Using this result, find the theoretical three-phase maximum power that can be transferred by the lossless transmission line.
A 500-kV, 300-km, 6()-Hz, three-phase overhead transmission line, assumed to be lossless, has a series inductance of 0.97 mH/krn per phase and a shunt capacitance of 0.0115F/km. per phase. (a) Determine the phase constant p, the surge impedance Zc, velocity of propagation v, and the wavelength of the line (b) Determine the voltage, current, real and reactive power at the sending end, and the percent voltage regulation of the line if the receiving-end load is 800 MW at 0.8 power factor lagging and at 500 kV.
A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of power. With VS=1 per unit, VR=0.9 per unit, λ =5000 km, Zc =500 V, and δ=36.878, determine a nominal voltagen level for the lossless transmission line based on Eq. (5.4.29) of the text. Using this result, find the theoretical three-phase maximum power that can be transferred by the lossless transmission line.
For a lossless trabsmisison line, the characteristic impedance is 80 ohm. If the capacitance per unit length is 1.5 mh/m then what will be the inductance per unit length.
A 50Ω lossless transmission line is terminated with a load impedance valued ZL = RL + jXL.According to what is given, a) RL for Voltage Standing Wave Ratio to be 2What should be the relationship between XL and?b) If RL = 100Ω, find the value of XL.c) Find the voltage minimum point closest to the load on the line.
A distortionless transmission line has a resistance per unit length of 0.5 ohm/m. If the characteristic impedance of the line is 50 ohm, them what will be the attenuation constant of the line in Neper (Np)/m?
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
An 8000 V, 60 Hz, single-phase, transmission line consists of two hard-drawn aluminumconductors with a radius of 2 cm spaced 1.2 m apart. If the transmission line is 30 km longand the temperature of the conductors is 200C,a. What is the series resistance per kilometer of this line?b. What is the series inductance per kilometer of this line?c. What is the shunt capacitance per kilometer of this line?
A)Ibc =? find the load current=? B)Vca calculate the line voltage =? C)Calculate the total complex power in the transmission line=?
A 500kV,300km,60Hz500kV,300km,60Hz, three-phase overhead transmission line, assumed to be lossless, has a series inductance of 0.97mH/km0.97mH/km per phase and a shunt capacitance of 0.0115mF/km0.0115mF/km per phase. Determine the phase constant ββ, the surge impedance ZcZc, velocity of propagation vv, and the wavelength λλ of the line. a. β=0.001259rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=4990kmβ=0.001259rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=4990km b. β=0.001259rad/km,Zc=290.43Ω,v=2.599×105km/s,λ=4990kmβ=0.001259rad/km,Zc=290.43Ω,v=2.599×105km/s,λ=4990km c. β=0.000629rad/km,Zc=290.43Ω,v=1.533×105km/s,λ=4990kmβ=0.000629rad/km,Zc=290.43Ω,v=1.533×105km/s,λ=4990km d. β=0.001049rad/km,Zc=290.43Ω,v=2.994×105km/s,λ=5998km
A lossless transmission line has 100 ? characteristic impedance. The line is terminated in a load impedance of 70-j100 ?. The maximum voltage measured on the line is 200V. Find;1. The minimum current and minimum voltage on the line2. Explain how location of voltage maximum can be determined by using load reflection coefficient from the forward and backward wave.3. Using load reflection coefficient in ii., calculate the distance from the load that produce the maximum voltage and current.
What are (a) the values of the intercept points in the load line and (b) the slope of the load line given the circuit?