Asap please thank youuu Read the question carefully before answering. Box or indicate your finalansurers when solving and draw your diagrams cleanly. Complete solutionplease. Use 2 decimal places when solving and for final answers. Drawthe PV and TS diagram with proper label of points when required.5. a 5-stage compressor has intake conditions of Wo kPa and 2000. Theair must be discharged at 900 kPa. Find the compressor work andheat rejected if the compression is isentropic, and the intercoolerpressures.

Answered: Image /qna-images/answer/526e646c-5629-4946-80c2-8d33a1b4f67d.jpg

5. A 5- stage compressor has intake conditions of Wo kPa and 200c. The air must be discharged at 900 kPa. Find the compressor work and heat rejected if the compression is isentropic, and the intercooler

5. A 5- stage compressor has intake conditions of Wo kPa and 200c. The air must be discharged at 900 kPa. Find the compressor work and heat rejected if the compression is isentropic, and the intercooler

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide a complete given and computation. Include all the decimals. A reheat cycle with two stages of reheating is executed, with steam expanding initially from 90 bar and 530'C. The two reheater pressure are 10 bar and 0.6 bar, and the steam leaves each reheater at 480'C. Condensation occurs at 0.04 bar. For an ideal cycle, find (a) QA and e. (b) For the engine, ignore the pressure drop through the reheaters, let the engine operate through the same states and compute W and e. (c) What is the steam flow rate for an engine output of 20,000kW?
Task 37. Discuss the need for superheated steam in a power generating plant (Provide a T-S diagram and show the difference in the amount of Wnet in the cycle)8. What limitations prevent the turbine inlet temperature to be superheated above 650º C?.
Provide a complete given and computation. Include all the decimals. A reheat cycle with two stages of reheating is executed with steam expanding initially from 20 MPa and 540C.The two reheater pressures are 3.8 MPa and 0.97 MPa, and the steam leaves each reheater at 540°C. Condensation occurs at 60°C. (a) For the ideal cycle and 1 kg/s of steam find Q,and e, (b) For the engine and 1 kg/s of steam find W and e.
Draw the layout of gas turbine plant which has two stage of compression with perfect inter-cooling. The high pressure turbine develops power enough only to drive the high pressure compressor. The low pressure turbine derives both the L.P compressor and load. Show the ideal process of this plant on T-S diagram.
Completely solve and box the final answers. Write legibly In a steam turbine plant, a single bleed is taken from the turbine for regenerative feed water heating (closed). The inlet of the turbine is supplied with steam at 3.4 MPa and 320 C and exhausts at 0.15 MPa for bled steam. The remaining will expand which in turn exhausts at 0.01 MPa. The working fluid is throttled via throttle valve after the closed feed water heater going to the condenser. By drawing the system and showing the process on T-s diagram determine (a) the mass fraction of the bled steam, then (b) the work net and the thermal efficiency of the system.
Use the steam tables provided and use 4 decimal places for solving. In an idealRankine cycle, steam first enters the turbine at 10 MPa and 400C. It expands to a pressure of 10 kPa. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Findthe quality of the steam,Qa, Qr, Wt, Wp, Wnet, efficiency, and steam rate
Solve the following problems and sketch the schematic diagram describing the system. Show pertinent and complete solutions. (steam table) A steam throttling valve with inlet conditions of 2MPa and 400C is connected to the inlet of the turbine. The turbine has 200kW power output and heat abstracted of 100kW. If the mass flow rate is 1kg/s and the exit temperature of steam is 300C, find the exit turbine pressure.
Use the steam tables provided and use 4 decimal places for solving. A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The maximum pressure of the cycle is 15 MPa, and the minimum pressure is 5 kPa. Steam initially enters the turbine at 500 C. a.) Draw the proper T-S diagram of the cycle with proper label for the points. b.) Find the qualityof the steam entering the condenser, Qa, Qr, Wt, Wp,Wnet,efficiency,mass flow rateand steam rate
Calculate the power required by a system of one compressor serving two evaporators. One evaporator carries a load of 40 kW at 12 degree C and the other a load of 70 kW at -6 degree C. A back pressure valve reduce the pressure in the 10 degree C evaporator to that of the -5 degree C evaporator. The condensing temperature is 37 degree C. The refrigerant is 134-A. What is the COP? With TS Diagram Use this Steam Table:https://docdro.id/VkxK8WH
2. A boiler produces a steam at 2.417 Mpa and 468.9oC. The steam enters a turbine where after the extraction of energy enters a steam condensing unit. The pressure inside the condenser is maintained at 0.1578 MPa. If the system operates on a simple Rankine cycle, solve for: a) heat added per cycle, b) heat rejected, c) cycle net work and d) the cycle thermal efficiency. (3 DECIMAL IN FINAL ANSWERS PLS THANK YOU)
Ill leave a thumbs up if you answer the following pls Determine the followig: a. The heat rejected in kj/kg in the condenser b. The cycle thermal efficiency c. The steam flow rate in kg/hr
Provide a complete given and computation. Include all the decimals. In a reheat cycle steam at 8.0 MPa and 485C enters the turbine and expands to 1.4 MPa. At this point, the steam is withdrawn and passed through a reheater. It re-enters the turbine at 1.3 MPa and 720°C. Expansion now occurs to the condenser pressure of 0.006 MPa.For the cycle and 1 kg of steam determine (a)the steam flow for an engine and (b) For the engine output of 40,000kW.