DZIA OeLe 9:09• Asiacell Iı.こ EEA docs.google.com70 ND120 N4550 N/m300 N.m301.5m1.5m3m2 m2 mblä 3the concentrated load whichreplaced by distributed load isequal toA

Answered: 70 N D 120 N 50 N/m 300 N.m 30 B 1.5m…

70 N D 120 N 50 N/m 300 N.m 30 B 1.5m 1.5m 3m 2 m 2 m Llä 3 the concentrated load which replaced by distributed load is equal to

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed. Kindly Use NSCP 2015 please for this problemHint Answers: 1,420.18
MACHINE DESIGN TOPIC A short compression member with Do = 2Di is tosupport a dead load of 25 tons. The material isto be 4130 steel, WQT 1100 F. Calculate theoutside and inside diameters in terms of incheson the basis of (a) yield strength, (b) ultimatestrength.*For 4130 steel, WQT 1100 FSu = 127 ksiSy = 114 ksi*Use the following Safety FactorsNu = 4Ny = 2
A load of F = 14 kN is applied to a circular chain link shaped on the right. em = 600 N / mm2What is the diameter of the chain link in order to carry the given load safely?
Evaluate and identify nearest value of the load that can be lifted to a height of 1000 cm in 0.50 minutes by a machine which has an input power of 0.65kW. a. Approximately 0.3 ton. b. Approximately 0.6 ton. c. Approximately 0.2 ton. d. Approximately 0.4 ton.
A W section is used as a column of hinged ends with a length of 6 m. Fy = 248 MPa and E = 200GPa.Use the formula for combined stress. Section properties:A = 21300 mm2Sx = 2080 x 10^3 mm^3rx = 119 mmSy = 746 × 10^3 mm^3ry = 68.10 mm Questions:Determine the safe distance along the plane of the web could an eccentric load of 197.6 kN be placed.Hint Answers: 1,420.18
23 MENG201 Mechanical workshop practice
Pls answer thank you! A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 600 mm. The generator output is 80 MW, 60 hz and 95 percent efficiency. If there are 18 bolts, determine the force acting on each bolt.
This is part of alarger super position problem and I was able to solve for a moment and a concentrated load but this distributed load is confusing me. E = 200 GPa I = 216*10^6 mm^4 w = 81 kN/m d = 1.5 m I ended up getting an answer near -12 mm of diflection but that is an incorrect according to the grader. What would the equation for the elastic curve of this problem be? What is its value at point B? thank you so much!
A load of F = 14kN is applied to a circular chain link in the figure. Since σem = 600 N / mm2What is the diameter of the chain link in order to safely carry the given load?
Chose the correct answer: 5. A point load is considered in a system: a) A load applied at a dimensionless point b) That the load is considered punctual is applied in an area that is considered small along the length of the beam c) That the load of the point load is small with respect to the length of the beam d) All of the above e) None of the above
A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central concentrated cyclic load having a minimum value of 20 kN and a maximum value of 50 kN. Take factor of safety of l.5, size effect of 0.85, and a surface finish factor of 0.9 . The material properties of bar are given as ultimatestrength of σu 625MPa, yield strength of σy 510MPa and endurance strength of σe 340MPA. Determine the diameter of bar by using Goodman's method and Soderberg method.
Please show a clear step-by-step solution. Thank you! What is the proportion of the alteration in length for Spring A to Spring B, supposing that both springs carry an equal amount of load? Springs A and B have the identical qualities, with the exception that Spring A has 12 times the number of turns as Spring B.