70. ||| A water pipe in a building delivers 1000 liters (with mass 1000 kg) of water per second. The water is moving through the pipe at 1.4 m/s. The pipe has a 90° bend, and the pipe will require a supporting structure, called a thrust block, at the bend, as in Figure P9.700. We can use the ideas of momentum and impulse to understand why. Each second, 1000 kg of water moving at vz = 1.4 m/s changes direction to move at Vy = 1.4 m/s. a. What are the magnitude and direction of the change in momentum of the 1000 kg of water? b. What are the magnitude and direction of the necessary impulse? c. This impulse takes place over 1.0 s. What is the necessary force?

70. ||| A water pipe in a building delivers 1000 liters (with mass 1000 kg) of water per second. The water is moving through the pipe at 1.4 m/s. The pipe has a 90° bend, and the pipe will require a supporting structure, called a thrust block, at the bend, as in Figure P9.700. We can use the ideas of momentum and impulse to understand why. Each second, 1000 kg of water moving at vz = 1.4 m/s changes direction to move at Vy = 1.4 m/s. a. What are the magnitude and direction of the change in momentum of the 1000 kg of water? b. What are the magnitude and direction of the necessary impulse? c. This impulse takes place over 1.0 s. What is the necessary force?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following particular refer to a two row velocity compounded Impulse steam turbine (wheel). Steam velocity at Nozzle exit-600 m/sec, Nozzle angle - 16°, Mean Blade velocity = 120 m/sec. Exit angles; first row of moving blades - 18° Fixed guide blades = 22⁰ Second row of moving blades 36° Steam flow rate=5kg/sec. Blade friction coefficient=0.85 Determine (1) Tangential thrust
6. The blade speed in a simple stage is 150 m/sec and the nozzle angle is 18 degrees. The velocity of the steam leaving the nozzles ia 320 m/sec and the bucket entrance and exit angles are both 33 degrees. The bucket velocity coefficient is 0.89. Find the relative velocity leaving the buckets, m/sec.A. 163.8 B. 173.8 C. 183.8 D. 193.8
Two centrifugal pumps are connected in series in a given pumping system. Plot total head Δh against capacity Q pump and system curves and determine the operating points for (a) only pump 1 running (b) only pump 2 running (c) both pumps running on the basis of the following data: operating data for pump 1 Δh1 m, 50.0 49.5 48.5 48.0 46.5 44.0 42.0 39.5 36.0 32.5 28.5 Q m3 /h, 0 25 50 75 100 125 150 175 200 225 250 operating data for pump 2 Δh2 m, 40.0 39.5 39.0 38.0 37.0 36.0 34.0 32.0 30.5 28.0 25.5 Q m3 /h, 0 25 50 75 100 125 150 175 200 225 250 data for system Δhs m, 35.0 37.0 40.0 43.5 46.5 50.5 54.5 59.5 66.0 72.5 80.0 Q m3 /h, 0 25 50 75 100 125 150 175 200 225 250
The following particulars refer to a two-row velocity-compounded impulse wheel which forms the first stage of a combination turbine: Steam velocity at nozzle outlet 630 m/s Mean blade velocity 125 m's Nozzle angle 16 Outlet angle, first row of moving blades :18° Outlet angle, fixed guide blades : 22° Outlet angle, second row of moving blades :36 Steam flow rate :2.6 kg/s The ratio of the relative velocity at outlet to that at inlet is 0.84 for all the blade. Determine (a) The velocity of whirl. (b) The tangential thrust on the blades. (c) The axial thrust on the blades. (d) The power developed. (e) The blading efficiency....solve with me 40 minutes
Derive an expression for the blade efficiency in reaction turbine that has four stages by means of flow and blade velocities with exit and entrance angles of moving blades if: the nozzle angle equal to twice the exit angle of moving blade, while the outlet relative velocity is equal to absolute velocity.If the efficiency of any stage is 90%, what is the total efficiency of this turbine
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps?
EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, r2 = 17.5 cm, By =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if by = b2 = 4.4 cm.(Hint. design point discharge, i.e 11=90°)
A centrifugal pump has the following characteristics as shown in Table 1. Table 1: Pump characteristics Q(m3 /s) 0.033 0.029 0.027 0.0235 0.020 0.017 0.0133 H(m) 40 60 66 75 80 84 90 Efficiency % 20 45 55 68 75 66 45 The pump is used to pump water from a low reservoir to a high reservoir through a total length of 1100 m of pipe 250 mm in diameter. The difference between the water levels in the reservoirs is 25 m. Neglecting all losses except friction and assuming λ=0.042, calculate: i. The discharge and head at the duty point for the pump. (20) ii. The efficiency at the duty point. (5) [2
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps? Assuming the head is equally divided between the two pumps, what is the efficiency of either pumps (in %)? Take the specific weight of water to be 62.4 lbf/ft3.
A Francis turbine has the following specifications. Inlet radius 300 mm, outer radius 150 mm, flow rate 0.05 m3/s, inlet guide blade 30 degree, angle the absolute velocity at exit makes an angle of 80 degree with the axis inlet absolute velocity 6 m/s, exit absolute velocity 3 m/s; overall efficiency 80%, hydraulic efficiency 90%. Determine head and power output if the angular velocity is 25 rad/s.
The following data are given for a certain rocket unit: Thrust, 8000 N Propellant weight flow rate, 36 N/sec Speed of rocket, 800 m/s internal efficiency32%combustion efficiency 97 % Determine (a) the effective velocity; (b) total kinetic energy per second (c) calorific value of propellant (d) the propulsive efficiency (e) the overall efficiency (f) the specific impulse (g) the specific propellant consumption ????? =1/3 ?(?^2) hV cylinder = ?(?^2) h V frustrum = 1/3 ?ℎ(?^2 +?^2 +? ×?)
EX1: Given are the following data for a commercial centrifugal water pump: r1 =10 cm, rz = 17.5 em, B1 =30°, B2 =20°, speed =1440 r/min. Estimate (a) the design point discharge, (b) the water horsepower, and (c) the head if bs = bz = 4.4 cm.(Hint. design point discharge, i.e €:=90°)