8-21. Determine if the base plate shown in Figure 8-58 is adequate for the given factored loads. Check the bearing strength of the concrete pier assuming f = 4 ksi. The steel used for the base plate is ASTM A572, Grade 50 steel. ructural Steel Design, Third Edition 30" 91 KIN H a) -W10x60 Pu-420k -16"x16"x1* pl. 16" 18" [I] b) FIGURE 8-58 Details for Exercise 8-21 -W12x58 Pu-500k 16"x18"x" pl.

8-21. Determine if the base plate shown in Figure 8-58 is adequate for the given factored loads. Check the bearing strength of the concrete pier assuming f = 4 ksi. The steel used for the base plate is ASTM A572, Grade 50 steel. ructural Steel Design, Third Edition 30" 91 KIN H a) -W10x60 Pu-420k -16"x16"x1* pl. 16" 18" [I] b) FIGURE 8-58 Details for Exercise 8-21 -W12x58 Pu-500k 16"x18"x" pl.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An axially loaded short spiral column is subjected to axial dead load of 620 KN and axial live load of 880 KN. Use f’c = 27.6 MPa, fy = 414 MPa, ρ = 0.025 and20 mm diameter main bars. Also, use 12 mm dia. ties with fyt = 276 MPa and clear concrete cover of 40 mm. Determine the following: a. Required diameter of the spiral column. b. Number of longitudinal reinforcement. c. Spacing of the spiral ties. Round off the answer into two decimal places
Design the base plate and pedestal for a W 310 X 86 column carrying D = 450 and L = 49OkN. Use fy = 250 MPa steel for column and base plate, fc' = 24 MPa psi for footing and pedestal, and Grade 400 reinforcing bars. The allowable soil pressure is 150 kPa. The pedestal is 1.40 m from the underside of the floor slab. Select two anchor bolts and draw a neat sketch of the column, plate, and anchor
Determine if the channel is adequate for the tension load Pu = 420 kN as shown. The channel is ASTM A-36 steel (Fy = 248 MPa, Fu = 400 MPa) and it is connected with four 16 mm diameter bolts. Determine the block shear strength of the section. Ubs = 1.0 Determine the strength based on gross yielding. Determine the strength based on tensile ruptuture.
a monotlithic floor framing plan, the columns are 300mm square, girders are 250mm wide by 450mm deep and slabs are 100mm thick. the floor loads include floor finish of 0.77kPa, ceiling system of 0.25 kPa, partition load of 1.0kPa and liveload of 4.8kPa. bar centroid from the edge of the beam is 70mm. calculate the ff: 1. total factored floor load in kPa 2. total factored uniform load on girder GH in kN/m 3. maximum ultimate bending moment at discontinuous end of girder GH in kN.m
Civil. Give ans please A250 mm wide and 600 mm deep R.C. beam is reinforced with 2 legged 10 mm inclined stirrups at 250 mm cle with a 60°. Longitudinal steel consists of 4 bars of 20 mm with a cover of 40 mm. If concrete grade is M25 and grade of steel is Fe 415, determine the strength of the section in shear.
PROBLEM: For the base plate shown in the attached figure:1) determine if the base plate is adequate for the given service loads. 2) check the bearing strength of the concrete pier assuming fc' = 28 MPa.The steel used for the base plate is A572 Grade 50.Use (a) LRFD and (b) ASD methods.
Badly need in 1hour thank u Compute the average shear stress that occurred in each of the 8-mm diameter bolts between the plates and the members and along each of the four shaded shear planes as shown if the axial force is 12 kN.
Determine the LRFD design strength, øPn , using 1) the AISC Equations; 2) Force_table4-1(Folio or manual); and 3) Stress_table4-14 (Folio or manual) for each of the compressionmembers shown. Use Fy= 50 ksi.
Aconcrete sectionwith b = 16 in. and d = 19.5 in. is required to develop a bending moment strength of Mr = 640 kip-ft. Use of compressivereinforcement is desired. Find the required reinforcement. Use f ′ c = 4 ksi and fy = 60 ksi.
An axially loaded short square column is subjected to axial dead load of 600 KN and axial live load of 1200 KN. Use f’c = 27.6 MPa, fy = 414 MPa, ρ = 0.025 and25 mm diameter main bars. Also, use 12 mm dia. ties with fyh = 275 MPa and clear concrete cover of 40 mm. Determine the following: a. Required column dimension. b. Number of longitudinal reinforcement. Round off the answer into two decimal places
PLEASE WRITE THE COMPLETE SOLUTION CLEARLY Design a square column for the given concentric axial loads. The column is appliedwith total dead load of 1000 kN and live load of 1400 kN. Use gross steel ratio ofapproximately 3%. fc’ = 28 Mpa , fy = 415 Mpa. Use 28mm bars for main bars and 10mm bars for ties.a. Compute for the required area of steel reinforcement,b. Recommend the number of 28 mm bars.c. Calculate the required spacing of ties.d. Draw/sketch the cross-sectional detail of the column.
Per the ACI, what is the minimum girder depth (Select a uniform depth for all girders) Material properties are:- Concrete weight: wt = 150 pcf- Concrete compressive strength: f’c = 4000 psi- Steel tensile strength: fy = 60 ksi- Stirrup consists of #4 bar- Framing members are not exposed to weather or in contact with soil. Answer from: 24", 30", 36", 28"