atmosphere. Water flows in the elbow at a rate of 0.03 m/s. The cross sectional area of the from the flow direction while accelerating it. The elbow discharges water into the ducing elbow in a horizontal pipe is used to deflect water flow by an angle of 0 = 45 %3D elbow is 150 cm2 at the inlet (point 1) and 25 cm? at the exit (point 2). The elevatio difference between the centers of the exit and inlet is 40 cm. The weight of elbow and water un it is considered negligible. Use density of the water p = 998 kg/m³ and momentum nux correction factor B = 1 for both inlet and exit. Determine a) Velocity of water at points 1 and 2 b) Gauge pressure at the inlet (point 1) c) Magnitude of the anchoring force needed to hold the elbow in place. %3D Az=25 cm² 45° A,= 150 cm? Zzj40 cm Water 30.0 kg/s

atmosphere. Water flows in the elbow at a rate of 0.03 m/s. The cross sectional area of the from the flow direction while accelerating it. The elbow discharges water into the ducing elbow in a horizontal pipe is used to deflect water flow by an angle of 0 = 45 %3D elbow is 150 cm2 at the inlet (point 1) and 25 cm? at the exit (point 2). The elevatio difference between the centers of the exit and inlet is 40 cm. The weight of elbow and water un it is considered negligible. Use density of the water p = 998 kg/m³ and momentum nux correction factor B = 1 for both inlet and exit. Determine a) Velocity of water at points 1 and 2 b) Gauge pressure at the inlet (point 1) c) Magnitude of the anchoring force needed to hold the elbow in place. %3D Az=25 cm² 45° A,= 150 cm? Zzj40 cm Water 30.0 kg/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
When a jet of water gushing from a short pipe with a diameter of D= 5 cm, located at a depth of h= 6.6 m from the surface of a fixed level reservoir shown in the figure, hits a horizontal plate that makes an angle of 30o with the jet axis (friction effects are neglected), a)Determine the scalar value and direction of the impact force exerted by the water on the plate (Enter the numerical value of the direction you think is correct in the direction-number image in Figure 3 in the box named "Direction-effect". For example: '1' will be entered for the upward direction). b)Determine the scalar value of the reaction force of the plate and determine its direction (Enter the numerical value of the direction you think is correct in the direction-number image given in Figure 3 in the box named "Direction-reaction". For example: '1' will be entered for the upward direction).
Water enters and leaves the 6-cm-diameter pipe bend inFig. P3.45 at an average velocity of 8.5 m/s. The horizontalforce to support the bend against momentum change is300 N. Find ( a ) the angle ϕ ; and ( b ) the vertical force onthe bend.
A U-tube acts like a water siphon. The elbow in the tube is 1 m above the water surface, the tube outlet is L from point A below. When the length L is 5 m, the water emerges from the bottom of the siphon as free jet at atmospheric pressure. Determine the speed of the free jet and the minimum absolute pressure of the water at the elbow. (Patm= 101325 Pa, dsu=1000 kg/m3)
Roman aqueduct customersobtained extra water by attaching a diffuser to theirpipe exits. Fig. shows a simulation: a smooth inletpipe, with or without a 15° conical diffuser expanding to a5-cm-diameter exit. The pipe entrance is sharp-edged. Calculatethe fl ow rate (a) without and (b) with the diffuser.
Water flows through a pipe of 0.0025 m^2size with a uniform velocity of 7m/s and flows out from an ariface at bottom at a rate 0.003 m^3/s. what is rate of change of mass of water in the tank?
4. Hydroelectric plants in the mountains bring water from a reservoir down to a turbine through enclosed tubes. In such plants, the 100 cm diameter intake tube (Point 2) in the dam is 50m below the water surface (Point 1) of the reservoir. The water drops 200 m through the tube before flowing into the turbine through a 50 cm diameter nozzle.
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Neglecting head losses, determinewhat horsepower the pump must deliver toproduce the flow as shown. Here theelevations at points A, B, C, and D are 110 ft.200 ft, 110 ft and 90 ft, respectively. The nozzle area is 0.10 ft2
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.