8. As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is required to support a load of 10KN if we are to neglect the weight of two pistons. (Answer must be in N)

8. As shown in the figure below, oil is inside the hydraulic press with SG=0.82. What force F is required to support a load of 10KN if we are to neglect the weight of two pistons. (Answer must be in N)

Name: ing water WitHspeciigravityandISCOSity0.002 poise.8.As shown in the f
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ing water WitHspeciigravityandISCOSity0.002 poise.8.As shown in the figure below, oil is inside thehydraulic press with SG=0.82. What force F is required tosupport a load of 10KN if we are to neglect the weight of twopistons. (Answer must be in N)10

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To what depth would a container of engine oil (sg=0.878) have to be filled to yield the same pressure at the bottom of a container with 8.25in of mercury (sg=13.55) ?
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a burs9ng disk is placed so that, if the pressure exceeds the maximum opera9ng pressure, the air is vented to atmosphere rather than over-pressuring the chemical reac9on vessel (Figures 4a and 4b). In this ques9on, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. a) You have a choice of five disks which can withstand the following forces across them before burs9ng: 10.5 kN, 11.0 kN, 11.5 kN, 12.0 kN, 12.5 kN. Which of these burs9ng disks would you recommend, and why? b) Due to an over-pressurisa9on of the air line, the disk bursts at 9me t = 0. At what pressure in the air line will this occur? c)…
Based on attached material, please solve following problem. A journal bearing of length 60 mm is to support a steady load of 20 kN. The journal, of diameter 50 mm, runs at 10 revolutions per second. Assuming c/R = 0.001 and ε = 0.6, determine a suitable viscosity of the oil, using the theory of (a) the very long bearing with the full Sommerfeld condition, (b) the very short bearing with the half Sommerfeld condition. For (a) determine the power required to overcome friction, and the best position for the oil supply hole relative to the load line. Would this position also be suitable according to theory (b)?
(Please no hand writing solution) What is the pressure at the bottom of 10,000 feet of methane (MW =16) if the surface pressure is 400 psia and the temperature is 640 R.
a 25 m high vertical column of a fluid of density 1800kg/m3 exists in a place where g= 9.6 m/s2 what is the pressure at the base of the column in psi?
Thin walled pressure vessel 3. Please provide proper discussion and illustration. Clear and complete solution please thank you.
An oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high. Find the minimum push required at the top of the drum. Take density of the oil as 1 kg/litre. Neglect weight of the drum. [Ans. 1444.5 N]
A block with specific gravity of SG= 1.45 and volume V= 0.75m3, is attached to a spring scale. The block is hung vertically such that it is fully submerged in oil ρoil= 0.85kg/m3 . a) Draw a free body diagram for the block. b) What is the apparent weight of the block?
PLEASE ANSWER THEM ASAP ALL FOR AN UPVOTE. I PROMISE THAT. At 20 0 C, determine pressure (in N/m²) inside a water droplet having diameter of 1.5 mm with a surface tension of 0.053 N/m. a.) What is the working formula of pressure to be used in this problem? b.)What is the diameter of the droplet (in m - enter your complete answer in decimal system)? c.) What is the radius of the droplet (in m - enter your complete answer in decimal system)? d.) What will be the modified working equation to be used to solve this problem based from the given? e.) What is the pressure inside the droplet of water (in N/m²)? f.)What is the pressure inside the droplet of water (converted to its CGS unit)?
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !
In the landing gear for the Airbus 320, engineers wish to design a damper (a device for reducingvibrations) consists of a metal plate 1mm thick moving centrally between two large plates. The gapsbetween the plate sides and side walls are both equal to 1mm. The area of the central plate is 4x10-4m2, and the damper is filled with liquid having a dynamic viscosity of 7.63poise. Calculate thedamping force on the central plate if the later moves at a velocity of 0.7m/s
A compressed air tank is designed to contain 50 standard cubic feet of air when filled to a gaugepressure of 200 atm at an ambient temperature of 70 F. Assume this is an air tank for scubadiving, and that the approximate shape of the tank is a cylinder with circular cross section. The interior volume of the tank is v=0.253 ft^3(a) If the interior length of the cylinder is 1 ft, what would be the inner diameter?(b) It is desired that the air tank be neutrally buoyant when empty. The density of aluminum is2700 kg/m3. If the tank is made of aluminum, what should be the wall thickness in order forit to be neutrally buoyant?