A vertical axis circular cylindrical wine storage tank, fabricated from stainless steel, has a total height of 8 m, a radius of 150 cm, and is filled to a depth of 6 m with wine. An inert gas occupies the 2-m height Ho above the gas-wine interface and is pressurized to a value of poof 80 kPa, as shown in Fig. If the working stress in the steel is 185 MPa, determine the required wall thickness. The specific weight of the wine is 9800 N/m³. Gas y=0. Ho H

A vertical axis circular cylindrical wine storage tank, fabricated from stainless steel, has a total height of 8 m, a radius of 150 cm, and is filled to a depth of 6 m with wine. An inert gas occupies the 2-m height Ho above the gas-wine interface and is pressurized to a value of poof 80 kPa, as shown in Fig. If the working stress in the steel is 185 MPa, determine the required wall thickness. The specific weight of the wine is 9800 N/m³. Gas y=0. Ho H

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.3P

See similar textbooks

Similar questions

A cylinder is fitted with a freely movable piston of area 1.20e-2m^2 and negligible mass. The cylinder below the piston is filled with a gas. At state 1 the gas has volume 1.50e-3m^3, pressure 1.02e5Pa, and the cylinder is in contact with a water bath at a temperature of 0.0C. The gas is then taken through the following four step process. - A 2.50kg metal block is placed on top of the piston, compressing the gas to state 2, with the gas still at 0.0 C. - The cylinder is then brought in contact with a boiling water bath, raising the gas temperature to 100C at state 3. - The metal block is removed and the gas expands to state 4 still at 100C. - Finally, the cylinder is again placed in contact with the water bath at 0C, returning the system to state 1. a) Determine the pressure of the gas in state 2. b) Determine the volume of the gas in state 2. C) Determine the volume of the gas in state 4. Answer all parts, ABC
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)
Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.
A piston cylinder device is equipped with a paddle-wheel driven by an external motor andis filled with gas. The walls of the cylinder, the piston, and the paddle-wheel and its shaft areall made of a material which is very good insulator. The system contains 50 g of gas.Initiallythe gas is in state A. The paddle-wheel is then operated, but the piston is allowed to move tokeep the pressure constant. Then the paddle-wheel is stopped, and the system is found to bestate B. There is very little friction between the piston and cylinder walls. Determine the energytransfer in joules along the paddle-wheel shaft. State A B P, bars 35 35 v, m3/kg 7.11 19.16 u, J/g 22.75 47.64 h/ J/g 47.64 164.69
a = 9.71 x 10-5 m² / s, p = 20) Semi-infinite cylinder (k = 237 W / m. ° C, 2702 kg / m³, C, = 896 J / kg. ° C) of diameter 15 cm is initially at 150 ° C. The cylinder is placed in water at 10 ° C, where heat transfer by convection with h = 140 W / m?. ° C. Determine a) temperature at center of cylinder 5 cm from end surface % 3D 8 min after start of cooling, b) total heat transfer.
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
A 2.5-m-tall steel cylinder has a cross-sectional area of 1.5 m2. At the bottom, with a height of 0.5 m, is liquid water, on top of which is a 1-m high layer of gasoline, relative density of 0.8. The gasoline surface is exposed to atmospheric air at 101 kPa. What is the gage pressure at the liquid interface?
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
Cylindrical vessel of 1m diameter and 4 m length has hydrogen gas at pressure of 100 kpa and 27 °C. Determine the amount of heat to be supplied so as to increase gas pressure to 125 kPa. For hydrogen take Cp= 14.307 kJ/kg K, Cv= 10.183 kJ/kg K.
Assume a temperature distribution of T= 288- 0.0065z K and integrate to find the pressure at 10 km in theatmosphere assuming p= 101.3 kPa at z= 0. Calculate the error.
1. A steel sphere 3” in diameter heated to 600oF, is to be cooled by immersion in an oil bath at 100oF. Calculate the average temperature of the sphere a) 10 sec and b) 6 min after immersion. For steel, k = 26Btu/ft-h-oF;  = 486lb/ft3 ; Cp = 0.11Btu/lboF.