9. 50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground surface as seen in the figure. Compute the vertical stress increment under Point D down to the depth z = 20 m. 7.5 m 150 kN 50 kN 2 m A 5 m B (Plane view) `100 kN 3 m

9. 50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground surface as seen in the figure. Compute the vertical stress increment under Point D down to the depth z = 20 m. 7.5 m 150 kN 50 kN 2 m A 5 m B (Plane view) `100 kN 3 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.13P: Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below...

See similar textbooks

Related questions

Q: If the gauge of the railroad shown on the plan above is 1.7 m and produces a line-like loading at…

Q: Refer to Figure P6.3. Determine the vertical stress increase Δσ at point A with the values q1 = 90…

A: Given: Line load 1, q1 = 90 kN/m Line load 2, q2 = 325 kN/m Distance between line loads, x1 = 4 m…

Q: The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2 : (1)…

A: Note- Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: 50 and 100 kN/m vertical line loads are applied on the ground surface as shown in the figure.…

A: For, load= 50 kN/m vertical stress = (2Q/Z) (1/[1+(x/z)])2 Q= 50kN/m x= 5m, Z = 30m Therefore,…

Q: 1. Determine the increase in vertical stress at a depth of 7 m below the point B. Point loads of…

A: using boussenique's equationσ=QZ232π11+rz25/2z=7 mr1=3 mr2=5 m

Q: Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2).…

A: Applying Boussinesq's Equation: ∆σz=3P2πz21+rz25/2 ...(1)

Q: 10.17 Refer to Figure 10.47 A flexible rectangular arca is subjected to a uniformly distributed load…

A: Introduction- Vertical stress is among the most significant pressures encountered by constrained…

Q: Ex3: 50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the ground…

Q: a) Point loads of 1000,5000, and 3000 lbs acts on point A, B, and C respectively. Determine the…

A: Note: Since you have posted a two different question. So as per guideline it is required to solve…

Q: Point loads of magnitude 10O, 200, and 400 kN act at A, B, and C, respectively. the increase in…

Q: 8.5 100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the…

Q: Using Boussinesq's Equation determine the vertical stress increase A6z, at point Cat a depth 3.0…

Q: 2. A rectangular loaded area ABCD shown in figure below carries a load of 80kN/m? Using Fadum chart…

A: Draw:

Q: 2. Given a rectangular area with dimensions of 2 m by 3 m and a load of 195 kN/m, hind the vertical…

Q: 10.17 Refer to Figure 10.47 A flexible rectangular area is subjected to a uniformly distributed load…

Q: A rectangular raft of size 26 x 10 m founded on the ground surface is subjected to a uniform…

A: Given Data: The total length of the raft is L=26 m. The total width of the raft is B=10 m. The…

Q: 10.17 Refer to Figure 10.47 A flexible rectangular area is subjected to a uniformly distributed load…

A: Introduction- Vertical stress is among the most significant pressures encountered by constrained…

Q: Point loads of magnitude 100, 200, and 400 kN act at A, B, and C, respectively. the increase in…

Q: Problem (4.4): Given: q= 100 kN/m. Find: The vertical stress o, at points 0, 1, and 2 shown in Fig.…

A: Uniformly Loaded Line of Finite Length Case: Consider the free body diagram of given loading on soil…

Q: Point loads of magnitude 100,200,and 400kN act at B, C, and D, respectively. Determine the increase…

A: Given :

Q: Q2/ For the uniformly distributed loaded area as shown below, estimate the vertical stress at point…

A: A uniformly distributed load (UDL) is a load that is distributed across the region of an element…

Q: B 6.0 m 6.p m 5.0 m Figure for Problem6

Q: 5 kN 2 kN 15 kN/m 50 mm P. E A 150 mm 3 m 1 m 3 m 1 m 150 mm

A: Free body diagram - RA + RE = 15×3 + 5 + 2⇒RA + RE = 52 KN .........1 Taking the sum of…

Q: Refer to Figure below. Point loads of magnitude 500 KN, 750 KN, 800 KN, and D00 KN act at A C. E,…

A: We will use boussinesq equation.

Q: Calculate the vertical stress at a depth of 50 ft below a point 10 ft oubide the corner (along the…

Q: Use the approximate method to estimate the stress (kPa) under the center of a rectangular loaded…

Q: 2- Point loads of magnitude 100, 200, 300 and 400 lbs. act at A, B, C, and D, respectively.…

A: Given Data: The point loads A, B, C and D are given as: QA = 100 lbsQB = 200 lbsQC = 300 lbsQD = 400…

Q: 10 ft Point loads of magnitude 2000, 4000, and 6000 lb act at A, B, and C, respectively as shown on…

A: Given: The point load at A is 2000 lb. The point load at B is 4000 lb. The point load at C is 6000…

Q: Н.О 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: The given data is: Load at point B (QB) = 100 kN Load at point C (QC) = 200 kN Load at point D (QD)…

Q: Consider a square-shaped area ABCD on the ground with its Centre at M as shown in the figure. Four…

A: Given:- Four concentrated loads are applied on the corners of the area ABCD The magnitude of the…

Q: Q13. Determine the total horizontal stress Op at point A if the lateral earth pressure at rest (K.)…

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 6.27). Determine…

Q: Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed load of q…

A: Given data, q = 330 kN/m2 z = 6 m L = 18 m B = 9 m Influence values are obtained from the given…

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface based on Boussinesq's…

A: Given data: A uniformly distributed line load of 500 kN/m. The ratio of vertical stress at a depth 2…

Q: 100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the…

Q: 10.7 Point loads of magnitude 125, 250, and 500 kN act at B, C, and D, respectively (Figure 10.40).…

A: To find out the increase of vertical stress at a depth of 10 m below the point of A.

Q: Ex2: An embankment shown in the figure is constructed. compute the vertical stress increment under…

Q: H.Q 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

Q: 1 A point load of 2000 KN is acting at the surface of a thick clay stratum. Compute the vertical…

A: Solution From boussinesq's equation, σz = IbQz2 Ib = 32π1+rz252 Substituting, z= 1m to 10 m and r=…

Q: Q.3) Determine the increase in vertical stress at a depth 4 m below point A due to surface loads…

Q: H.Q 5 Figure below shows an embankment load on a silty clay soil layer. Determine the stress…

Q: 100 kN point loạd and 40 kN/m line load are applied on the ground. surface as shown. Compute the…

Q: 5- A flexible rectangular area is subjected to a uniformly distributed load of q=250 Ib/ft.…

A: Given Data:L=6B=3q=250lb/ft2=4500lbz=6ft

Q: H.Q 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: Given that: Point load at B, QB=100 kN Point load at C, QC=200 kN…

Q: . Three point loads, 19000, 20000 and 18000kN, act in line 8 m, 6m apart near the surface of a soil…

A: Given three point loads that are 8m and 6m apart near the surface of soil mass. It is required to…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

A: The given data is: γ=18 KN/m3Depth of consideration z=6 m

Q: Refer to Figure, q1 = 90 kN/m; q2 %3D 325 kN/m; x1 = 4 m; x2 = 2.5 m; z = 3 m. the vertical stress…

Q: 1. Given a concentrated load of 200,000 lbs, find the vertical stress (p) at a depth of 15 ft and 10…

A: As per our guidelines we are supposed to answer only one question. Kindly repost the other questions…

Q: CEN-333 Geotechnical

A: Boussinqi's equation: σZ=QZr32π11+rZ252where,Z=Depth of the pointQ=point load actingr=radial…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

9. 50, 100, and 150 kN point loads are applied at Points A, B, and C, respectively, on the
ground surface as seen in the figure. Compute the vertical stress increment under Point D down
to the depth z = 20 m.
7.5 m
150 kN
50 kN
2 m
C
A
5 m
B
(Plane view)
`100 kN
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the ground. Compute the total vertical stress in kN/m^2 increment due to this unifrom load if the unit weight of soil is 18.40 kN/m^3 at point 6 m below the edge of the circular area. a. 18.62 b. 137.66 c. 115.17 d. 129.02
Refer to Figure 10.47. A exible rectangular area is subjected to a uniformly distributed load of q 5 330 kN/m2. Determine the increase in vertical stress, Dz, at a depth of z 5 6 m under points A, B, and C .details about me sending through pictures
Given that: • stress contributed by q1 = 0.73 KN/m² • total increase in vertical stress = 46.36 KN/m² • if the magnitude of the two loads is combined as one, the horizontal distance = 1.80m Answer the ff: a) The stress contributed by q2 is b) What is the equivalent horizontal load if it is located 3 meters away from point A given that the said point experiences the same vertical stress increase given by the set-up? Note: Point A is at the same depth
How should the groundwater table move to have an effective stress of 95kPA, 2m from the bottom of the profile? For specific gravity, Gs = 2.68.
Soil with a unit weight of 16.97 kN/m^3 is loaded on the ground surface by a uniformly distributed load of 300 kN/m^3 over a circular area 4 m in diameter. Compute the total vertical stress increment due to this uniform load at a depth of 5 m below the center of the circular area. a.60 b.144.8 c.232.49 d.714
Figure below shows a 100 kN point load and 40 kN/m line load are applied on the ground surface. Calculate the vertical stress at the depth z=5 m directly underneath of Points A and B.
Consider the soil profile shown inFigure 1.4: How high should thegroundwater table rise/drop so thatthe effective stress at C is 130 kN/m2?
A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the ground. Compute the total vertical stress in kN/m^2 increment due to this uniform load if the unit weight of soil is 18.40 kN/m^3 at point 6 m below the center of the circular area. a. 27.26 b. 137.66 c. 129.02 d. 135.17
Calculate the vertical stress at a depth of 50 ft below a point 10 ft oubide the corner (along the longer side) of a rectangular loaded area 30 x 80 ft carrying a uniform load of 2500 lb/ft2 .
In the figure shows a plan view of footing that applies a uniform load of 300kPa on a horizontal ground surface. Calculate the vertical stress component in kPa at point A at a depth of 2m.
Subject : Geotechnical Engineering If you don't know the solution please leave it. The plan of a flexible rectangular loaded area is shown. The uniformly distributed load on the flexible area (q) is 400 kN/m^2. Determine the increase in the vertical stress at a depth of z = 1m, 2m, and 3m below.