Answered: 2. A rectangular loaded area ABCD shown…

2. A rectangular loaded area ABCD shown in figure below carries a load of 80kN/m? Using Fadum chart find the vertical stress increment at a depth of 3 m below point G. 0.6 m 0.6 m 1.5 m D.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.18P: Refer to the flexible loaded rectangular area shown in Figure 10.47. Using Eq. (10.36), determine...

See similar textbooks

Related questions

Q: 15 m C IN 2 3.5 m 3.5 m BA 2 Unit weight y = 19 kN/m³ 8 m ↓

Q: subject - geotechnical design book - principle of foundation engineering

A: We have the following formula for vertical stress:

Q: Practice Problem: Refer to Figure 3.70, a flexible square area is subjected to a uniformly…

A: Given: The distributed load (q) is 100 kN/m2. The depth is 4 m. Consider the figure,

Q: Determine the stress increase due to the embankment load at point A as shown in Figure 2. The unit…

A: Draw the figure.

Q: 1. Determine the increase in vertical stress at a depth of 7 m below the point B. Point loads of…

A: using boussenique's equationσ=QZ232π11+rz25/2z=7 mr1=3 mr2=5 m

Q: Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2).…

A: Applying Boussinesq's Equation: ∆σz=3P2πz21+rz25/2 ...(1)

Q: Compute the vertical stress increments under Points A, B,

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 8.23). Determine…

A: Boussinesq’s formula for calculating stress below point load:

Q: subject : Geotechnical Design Book : PRINCIPLE OF FOUNDATION ENGINEERING

A: We are given the following data

Q: A flexible rectangular area 3m by 2m is subjected to a uniformly distributed load of q = 200 kN/m2.…

Q: 8.5 100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the…

Q: Using Boussinesq's Equation determine the vertical stress increase A6z, at point Cat a depth 3.0…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

Q: The plan of a flexible circular loaded area is resisting the uniformly distributed load (q), 835…

Q: Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A…

A: The embankment with sloping side show the trapezoidal load. It is necessary to calculate the…

Q: 10.17 Refer to Figure 10.47 A flexible rectangular area is subjected to a uniformly distributed load…

Q: Using equation 6.14, determine the vertical stress (Aoz) increase below the center of paded area at…

A: Given Area = 6.35*3.35m^2 Depth 2m,4,6,8,10m q= 225kn/m^2 Calculate stress at different different…

Q: Problem 3.7 For the seepage situations shown in Figure, determine the effective normal stress on…

A: Solution1By considering pore water pressure::σ'=σ-uσ=20×2+3×9.81=69.43KPau=1+39.81=39.24σ'=30.2kpaBy…

Q: Calculate the effective stress at A. 25 m Sand and- Gravel Water Table Unit Weight (y) = 20.72 kN/m…

A: Following is the given soil profile:

Q: SITUATION. From the soil profile shown below, Ground surface Dry Sand Clay A e = 0.49 Gs=2.68 Ground…

Q: Q2/ For the uniformly distributed loaded area as shown below, estimate the vertical stress at point…

A: A uniformly distributed load (UDL) is a load that is distributed across the region of an element…

Q: 10.17 Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed…

A: Given :

Q: Use Eq. (6.14) to determine the stress increase Δσ at z = 10 ft below the center of the area…

A: Solution; Calculate parameter m1 as follows: m1=LBHere,The width of the foundation =B=10 ftLength of…

Q: | A uniformly distributed line load of 500 kN/m is acting on the ground surface. Based on…

A: Given data: A uniformly distributed line load, q' = 500 kN/m

Q: 2m Dry zone Soil properties: Gs = 2.68 A e = 0.85 В 1.8 m Saturation zone (capillary rise) 0.9 m D…

A: The soil properties are given Specific gravity of solids, Gs = 2.68 Void ratio, e =0.85 The total…

Q: 10 ft Point loads of magnitude 2000, 4000, and 6000 lb act at A, B, and C, respectively as shown on…

A: Given: The point load at A is 2000 lb. The point load at B is 4000 lb. The point load at C is 6000…

Q: Calculate the stress distribution with depth below the center of the dam, and the stres distribution…

Q: Consider a circularly loaded flexible area on the ground surface. Given: radius of the circular…

A: The increased in stress under the soil is happen by lots of situation like excess load over the…

Q: Н.О 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: The given data is: Load at point B (QB) = 100 kN Load at point C (QC) = 200 kN Load at point D (QD)…

Q: Figure 9.32 shows an embankment load for a silty clay soil layer. Determine the vertical stress…

A: We have to determine the value of vertical stress increase at point A,B,C and we have tolhe data…

Q: Consider a square-shaped area ABCD on the ground with its Centre at M as shown in the figure. Four…

A: Given:- Four concentrated loads are applied on the corners of the area ABCD The magnitude of the…

Q: Q13. Determine the total horizontal stress Op at point A if the lateral earth pressure at rest (K.)…

Q: show the variation beneath the edge of the loaded area.

A: Consider the following equation : σz=q1-11+r2232 Here r= 5ft Plot the variation of the vertical…

Q: Ex2: An embankment shown in the figure is constructed. compute the vertical stress increment under…

Q: Layer No. Thickness, H Soil Parameters e = 0.52, Gs = 2.62 e = 0.56, Gs = 2.65 w = 20%, e = 0.51 1…

Q: Problem No. 1 An earth embankment diagram is shown in Figure. Determine the stress increase at point…

A: I try to give detail and neat explanation for this question, so if possible give me a feed back plz?…

Q: An earth embankment is shown in Figure 3.4. Determine the stress increase at t A due to the…

Q: Figure below shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: 10.15 For the embankment shown in Figure 10.45, determine the vertical stress increases at points A,…

A: - Total load of embankment per meter length is, Length of base = 10+(22.5*2.25*2)=111.25 m Q=Unit…

Q: Determine the vertical stress increase, Aoz, at point A with the following values: q1 = 90 KN/m; q2…

A: Given: Line loads Vertical distance Radial distance To find: Vertical stress increase at point A to…

Q: 9.) For linear stress variation over the base of the dam of Fig. 47, find where the resultant…

Q: 4. The plan of a flexible rectangular loaded area is shown in the figure below. The uniformly…

Q: The plan of a flexible rectangular loaded area is shown in Figure 6.30. The uniformly distributed…

A: Solution: The equation for determining the increase in stress on a flexible rectangular area at a…

Q: An earth embankment is shown in the figure. Determine the stress increase at 2. point A due to the…

A: Given that...

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

A: The given data is: γ=18 KN/m3Depth of consideration z=6 m

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

Question

2.
A rectangular loaded area ABCD shown in figure below carries a load of 80kN/m?
Using Fadum chart find the vertical stress increment at a depth of 3 m below point
G.
0.6 m
0.6 m
1.5 m
D.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Refer to the flexible loaded rectangular area shown in Figure 10.47. Using Eq. (10.36), determine the vertical stress increase below the center of the loaded area at depths z = 3, 6, 9, 12, and 15 m. Figure 10.47
For the same line loads given in Problem 10.8, determine the vertical stress increase, z, at a point located 4 m below the line load, q2. Refer to Figure 10.41. Determine the vertical stress increase, z, at point A with the following values: q1 = 110 kN/m, q2 = 440 kN/m, x1 = 6 m, x2 = 3 m, and z = 4 m. Figure 10.41
Redo Problem 6.12 using Figure 6.15. 6.12 Refer to Problem 6.1. Using Eqs. (6.3) and (6.29), estimate the average stress increase (av) below the center of the loaded area between depths of 3 m and 6 m. 6.1 A flexible circular area is subjected to a uniformly distributed load of 150 kN/m2 (Figure 6.2). The diameter of the load area is 2 m. Determine the stress increase in a soil mass at points located 3 m below the loaded area at r = 0, 0.4 m, 0.8 m, and 1 m. Use Boussinesqs solution. Figure 6.2 Increase in pressure under a uniformly loaded flexible circular area
The soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2:(1) Please use Mohr circle to draw the soil stress state(2) Calculate the maximum principal stress σ1 and the minimum principal stress σ3(3) Please find the (pole) position(4) What is the angle of intersection between the maximum principal stress surface and the horizontal plane?
Referring in the Fig. 2 below, B = 6m and q =150 kPa. For Point P, z = 2m and x = 1.5m. Determine the vertical stress at Point P.
For the embankment shown in Figure 10.45, determine the vertical stress increases at points A, B, and C
Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed load of q = 330 kN/m2 . Determine the increase in vertical stress, Δσz , at a depth of z = 6 m under points A, B, and C
An embankment consists of clay fill for which c=25 kPa and angle of internal friction is 260 (from consolidated undrained test with pore pressure measurement) The weight of fill per unit volume is 18.64 kN/m3. Compute the effective stress in kPa at a depth of 20 m. If the pore pressure at this point is shown by a piezometer to be 180 kPa. a. 62.5 b. 372.8 c. 192.8 d. 21.6
A strip load of q =53 kN/m^3 is applied over a width B =11m. Determine the increase in vertical stress in kPa at point A located z = 4.6 m below the surface. x = 8.2m
5. A thick layer of stiff saturated clay is underlain by a layer of sand under artesian pressure. A deep cut is made in the clay layer as shown in the attached figure. Determine: [2] a. The total stress at point A. b. The factor of safety against heaving at point A, if the effective stress is 12% of the total stress.
Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively(Figure 6.27). Determine the increase in vertical stress at a depth of 3 mbelow point D. Using Westergaard solution. Use μs = 0.4.