Answered: 9. A conical tank is 12 ft. across the…

Name: 9. A conical tank is 12 ft. across the top and 8 ft. deep. It contain
Uploaded: 2024-03-20T06:56:46.000Z
Channel: Bartleby
Description: 9. A conical tank is 12 ft. across the top and 8 ft. deep. It contains water to adepth of 6 ft. Find the work done in pumping the water to a point 2 ft. abovethe top of the tank.2/3

Science

Physics

9. A conical tank is 12 ft. across the top and 8 ft. deep. It contains water to a depth of 6 ft. Find the work done in pumping the water to a point 2 ft. above the top of the tank.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 26CQ: Some chimney pipes have a T-shape, with a crosspiece on top that helps draw up gases whenever there...

See similar textbooks

Similar questions

A sump pump (used to drain water from be basement of houses built below the water table) is draining a flooded basement at rate of 0.750 L/S, with an output pressure of 3.00105N/m2 . (a) The water enters a hose with a 3.00-cm inside diameter and rises 2.50 m above the pump. What is its pressure at this point? (b) The hose goes over the foundation wall, losing 0.500 m in height and widens to 4.00 cm in diameter. What is the pressure now? You may neglect frictional losses both parts of the problem.
Check Your Understanding If the reservoir in Example 14.1 covered twice the area, but was kept to the same depth, would the dam need to be redesigned?
How much work is required to pump all the water over the top of a full cylindrical task that is 2 m diameter and 7 m height? (Unit of work = Joules, J). specific weight of water = 9.81 kN/m³
A conical tank with height 10 and radius 2 is filled to the top with a liquid weighing 15 N/m3 . How much work spent pumping all of the liquid out of the tank through the top?
2. (6413 #5 p. 351) A water tank is in the shape of a cone with the vertex down (Just like a cone ofice cream). The cone is 15 feet deep and the radius of the top is 10 feet. The cone is full of salt waterwith a density of 63 pounds per cubic foot. Setup, but do not evaluate, an integral which would givethe work done in pumping all the water to a level 4 feet above the top of the cone. The amount ofwork done is 244,125 π foot-pounds.
How much work is required to pump all the water over the top of a full cylindrical tank that is 4 m in diameter and 7 m high? (Unit of work= Joules, J) Specific weight of water = 9.81 kN/m³
A cylindrical tank of radius 3 ft and height 10 ft stands on aflatform 50 ft high. How much work will be done in fillingthe tank by pumping the water from the ground level?
A tank, shaped like a cone has height 4 meter and base radius 1 meter. It is placed so that the circular part is upward. It is full of water, and we have to pump it all out by a pipe that is always leveled at the surface of the water. Assume that a cubic meter of water weighs 10000N, i.e. the density of water is 10000N/m3. How much work does it require to pump all water out of the tank? Enter the exact value of your answer.
A horizontal cylindrical tank 4ft in the diameter and 10ft long is full of water. Find the work done in pumping the water to a point 4ft above the top of the tank.
A cylindrical tank, buried on its side, has radius 3 feet and length 10 feet. It is filled completely with water whose weight density is 62.4 lbs/ft3, and the top of the tank is two feet underground. How much work is required to empty the water in the tank to a truck whose tank lies 4.5 feet above the ground?
A conical tank is 12ft across the top and 8 ft deep. If contains water to a depth of 6ft. Find the work done in pumping the water to a point 2ft above the top of the tank.
8. Find the work done by pumping out molasses from a conical tank filled to 2ft from the top of the tank. The tank has a maximum radius of 3ft and a height of 10ft. molasses weighs 100lb/ft³.